Agilent Technologies 86100A Manual de servicio Pagina 49
- Pagina / 364
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
1-45
Introduction
Commands Unavailable in Jitter Mode
WAveform
Memory Display
Waveform memories cannot be turned on in Jitter mode. The following command produces a
"Settings conflict" error when executed in Jitter mode.
WMEMory<N>:DISPlay 26-2
Waveform and
Color Grade-Gray
Scale Memory
The Waveform and Color Grade/Gray Scale memories cannot be turned on in Jitter mode. The
following command produces an "Illegal parameter value" error when executed in Jitter
mode.
VIEW 4-15
When used with arguments other than JDMemory.
Timebase Scale
And Delay
Scale and position controls on the Horizontal setup dialog are disabled in Jitter Mode. The fol-
lowing commands produce a "Settings conflict" error when executed in Jitter Mode:
TIMebase:RANGe 23-4
TIMebase:SCALe 23-5
TIMebase:POSition 23-2
Channel Scale
And Offset
Channel scale and offset controls are disabled in Jitter mode. The following commands pro-
duce a "Settings conflict" error when executed in Jitter Mode.
CHANnel<N>:OFFSet 8-4
CHANnel<N>:RANGe 8-5
CHANnel<N>:SCALe 8-6
Acquisition
Settings
Acquisition (Averaging) controls are disabled in Jitter mode. The following commands pro-
duce a "Settings conflict" error when executed in Jitter mode.
ACQuire:AVERage 6-2
ACQuire:BEST 6-2
ACQuire:POINts 6-3
Histograms Histograms are turned off when entering Jitter mode. The following commands produce a
"Control is set to default" error.
HISTogram:MODE 14-3
VIEW 4-15
Software
Skewing of
Channels
All skew adjustments are disabled in jitter mode. The following commands produce a "Set-
tings conflict" error when executed in Jitter mode.
CALibrate:SKEW 7-9
CALibrate:SKEW:AUTO 7-10
- Infiniium DCA and DCA-J 1
- Agilent 86100A/B/C 1
- Wide-Bandwidth 1
- Oscilloscope 1
- Contents 3
- Contents-2 4
- ContentsContents 4
- Starting a Program 8
- Multiple Databases 10
- Status Reporting 15
- Introduction 18
- Command Syntax 27
- Figure 1-5. Command Tree 33
- Command Tree (Continued) 34
- Interface Functions 38
- Language Compatibility 40
- New and Revised Commands 46
- Error Messages 50
- Sample C Programs 57
- Initializing the Analyzer 66
- Setting Up a Service Request 67
- Generating a Service Request 68
- Sample Programs 104
- Common Commands 105
- *ESR? (Event Status Register) 107
- *IDN? (Identification Number) 108
- *LRN? (Learn) 109
- *OPC (Operation Complete) 109
- *OPT? (Option) 111
- *RCL (Recall) 111
- *RST (Reset) 111
- *SAV (Save) 116
- *SRE (Service Request Enable) 116
- *STB? (Status Byte) 117
- *TRG (Trigger) 117
- *TST? (Test) 118
- *WAI (Wait-to-Continue) 118
- Root Level Commands 121
- AUToscale 123
- CDISplay 125
- COMMents 125
- DIGitize 126
- RECall:SETup 132
- STORe:SETup 133
- STORe:WAVeform 134
- System Commands 137
- Table 5-1. Error Messages 140
- LONGform 141
- Acquire Commands 145
- SSCReen:AREA 149
- SSCReen:IMAGe 150
- SWAVeform 150
- SWAVeform:RESet 151
- Calibration Commands 153
- CONTinue 156
- ERATio:DLEVel? 156
- ERATio:STARt 156
- ERATio:STATus? 156
- FRAMe:LABel 157
- FRAMe:STARt 157
- FRAMe:TIME? 157
- MODule:LRESistance 157
- MODule:OCONversion? 158
- MODule:OPOWer 158
- MODule:OPTical 158
- MODule:OWAVelength 158
- MODule:STATus? 159
- MODule:TIME? 159
- MODule:VERTical 159
- RECommend? 160
- SAMPlers 160
- SKEW:AUTO 162
- Channel Commands 163
- FDEScription? 165
- PROBe:CALibrate 166
- PROBe:SELect 167
- UNITs:ATTenuation 169
- UNITs:OFFSet 169
- WAVelength 170
- Clock Recovery Commands 171
- CLBandwidth 174
- LBANdwidth 175
- ODRatio:AUTO 177
- RDIVider 179
- SPResent? 179
- TDENsity? 180
- Disk Commands 181
- DIRectory? 183
- MDIRectory 184
- PWAVeform:LOAD 184
- PWAVeform:PPBit 185
- PWAVeform:RANGe 185
- PWAVeform:RANGe:STARt 185
- PWAVeform:RANGe:STOP 186
- PWAVeform:SAVE 186
- D:\User Files\screen images 187
- Valid Filenames 187
- SPARameter:SAVE 188
- Display Commands 191
- DCOLor (Default COLor) 193
- GRATicule 193
- JITTer:BATHtub:YSCale 194
- JITTer:GRAPh 194
- JITTer:HISTogram:YSCale 194
- JITTer:LAYout 195
- JITTer:PJWFrequency 195
- JITTer:PJWTracking 195
- JITTer:SHADe 195
- LABel:DALL 196
- PERSistence 196
- Function Commands 201
- FUNCtion<N>? 203
- HORizontal 204
- HORizontal:POSition 204
- HORizontal:RANGe 205
- MULTiply 206
- SUBTract 207
- VERTical 208
- VERTical:OFFSet 208
- VERTical:RANGe 209
- Hardcopy Commands 211
- PRINters? 214
- Histogram Commands 215
- SCALe:SIZE 217
- WINDow:BORDer 218
- WINDow:DEFault 218
- WINDow:SOURce 218
- WINDow:X1Position 219
- WINDow:X2Position 219
- WINDow:Y1Position 220
- WINDow:Y2Position 220
- Limit Test Commands 221
- SSUMmary 227
- 30 ENTER 707;ULIM$ 230
- Marker Commands 231
- RPANnotation 233
- X1Position 233
- X1Y1source 234
- X2Position 234
- X2Y2source 235
- Y1Position 235
- Y2Position 236
- Mask Test Commands 237
- AOPTimize 239
- COUNt:FAILures? 240
- COUNt:FSAMples? 240
- COUNt:HITS? 240
- COUNt:SAMPles? 241
- COUNt:WAVeforms? 241
- MASK:DELete 242
- MMARgin:PERCent 242
- MMARgin:STATe 242
- SCALe:DEFault 243
- SCALe:MODE 244
- SCALe:SOURce? 244
- SCALe:X1 244
- SCALe:XDELta 245
- SCALe:Y1 245
- SCALe:Y2 245
- SCALe:YTRack 246
- Measure Commands 251
- ANNotation 253
- CGRade:AMPLitude 254
- CGRade:BITRate 254
- CGRade:COMPlete 255
- CGRade:CRATio 255
- CGRade:CROSsing 256
- CGRade:DCDistortion 256
- CGRade:DCYCle 256
- CGRade:EHEight 257
- CGRade:ERATio 257
- CGRade:ERFactor 258
- CGRade:ESN 258
- CGRade:EWIDth 258
- CGRade:JITTer 259
- CGRade:OFACtor 259
- CGRade:OLEVel 259
- CGRade:PEAK? 260
- CGRade:PWIDth 260
- CGRade:SOURce 260
- CGRade:ZLEVel 261
- DELTatime 263
- DUTYcycle 264
- FALLtime 264
- FREQuency 265
- HISTogram:HITS? 266
- HISTogram:M1S? 266
- HISTogram:M2S? 266
- HISTogram:M3S? 267
- HISTogram:MEAN? 267
- HISTogram:MEDian? 267
- HISTogram:PEAK? 267
- HISTogram:PP? 268
- HISTogram:PPOSition? 268
- HISTogram:SCALe? 268
- HISTogram:STDDev? 269
- JITTer:DCD? 269
- JITTer:DDJ? 269
- JITTer:DDJVsbit? 269
- JITTer:DDJVsbit:EARLiest? 270
- JITTer:DDJVsbit:LATest? 270
- JITTer:DJ? 270
- JITTer:EBITs? 270
- JITTer:EDGE 271
- JITTer:FREQuency:ANALysis 271
- JITTer:FREQuency:COMPonents? 271
- JITTer:FREQuency:MAXNumber 272
- JITTer:FREQuency:SCAN 272
- JITTer:ISI? 272
- JITTer:LEVel? 272
- JITTer:LEVel:DEFine 273
- JITTer:PATTern? 273
- JITTer:PJ? 273
- JITTer:PJRMS? 274
- JITTer:RJ? 274
- JITTer:RJSTabilize 274
- JITTer:RJSValue 274
- JITTer:SIGNal 275
- JITTer:SIGNal:AUTodetect 275
- JITTer:TJ? 275
- JITTer:TJ:DEFine 275
- JITTer:UNITs 276
- OVERshoot 276
- RESults? 278
- Table 18-2. Results Values 279
- Table 18-3. Result States 280
- RISetime 281
- SENDvalid 281
- TDR:AVERage 283
- VAMPlitude 285
- VAVerage 286
- S-Parameter Commands 291
- TDRSparam 293
- MAGGraph:HORizontal:STARt 293
- MAGGraph:HORizontal:SPAN 293
- MAGGraph:VERTical:MAXimum 294
- MAGGraph:VERTical:MINimum 294
- MARKer:X1STate 294
- MARKer:X2STate 294
- MARKer:X1Source 294
- MARKer:X2Source 295
- MARKer:X1Position 295
- MARKer:X2Position 295
- MARKer:Y1Position? 295
- MARKer:Y2Position? 296
- MARKer:XDELta? 296
- MARKer:YDELta? 296
- Signal Processing Commands 297
- LFEQualizer:BANDwidth 299
- LFEQualizer:BWMode 299
- LFEQualizer:FDELay 299
- LFEQualizer:NTAPs 299
- LFEQualizer:TAP 300
- LFEQualizer:TAP:AUTomatic 300
- LFEQualizer:TAP:NORMalize 300
- LFEQualizer:TDELay 300
- LFEQualizer:TDMode 300
- MATLab:ETENable 301
- MATLab:ETEXt 301
- MATLab:SCRipt 301
- SOURce:DISPlay 302
- TDR/TDT Commands 303
- (Rev. A.05.00 and Below) 303
- RESPonse 306
- RESPonse:CALibrate 306
- RESPonse:CALibrate:CANCel 307
- RESPonse:CALibrate:CONTinue 307
- RESPonse:HORizontal 308
- RESPonse:HORizontal:POSition 308
- RESPonse:HORizontal:RANGe 308
- RESPonse:RISetime 309
- RESPonse:TDRDest 309
- RESPonse:TDRTDT 310
- RESPonse:TDTDest 310
- RESPonse:VERTical 311
- RESPonse:VERTical:OFFSet 311
- RESPonse:VERTical:RANGe 312
- STIMulus 312
- (Rev. A.06.00 and Above) 315
- DUT:DIRection 318
- DUT:TYPE 318
- RESPonse:DISPlay 320
- RESPonse:RPLane? 321
- RESPonse:TYPE 321
- RESPonse:VAMPlitude? 321
- RESPonse:VLOad? 323
- STIMulus:EXTernal 323
- STIMulus:EXTernal:POLarity 323
- STIMulus:MODE 324
- STIMulus:RATE 324
- STIMulus:STATe 324
- Timebase Commands 325
- PRECision 327
- PRECision:RFRequency 327
- PRECision:TREFerence 328
- REFerence 328
- Trigger Commands 331
- DCDRatio 333
- DCDRatio:AUTodetect 333
- HYSTeresis 334
- PLENgth:AUTodetect 334
- PLOCk:AUTodetect 335
- Waveform Commands 337
- BANDpass? 339
- BYTeorder 339
- PREamble 343
- SOURce:CGRade 346
- XDISplay? 347
- XINCrement? 347
- XORigin? 347
- XREFerence? 348
- YDISplay? 348
- YINCrement? 349
- YORigin? 349
- YREFerence? 349
- Waveform Memory Commands 351
- XOFFset 353
- Index-10 364
Relacionado con productos y manuales para De medición, control y control Agilent Technologies 86100A
(9 paginas)
(18 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.030 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales