Agilent Technologies HP 8566B Manual de usuario descargar pdf (Pagina 14)

Inputs

RF input 100 Hz to 22 GHz, precision type-N female connector, dc-coupled

Maximum input level

ac Continuous power: +30 dBm from 50 ohm source

Mixer protected by diode limiter, 100 Hz-2.5 GHz

Pulse power: ≤ 100 W, 10 µs pulse width with ≥ 50 dB input attenuation

(≤ 0 dBm peak power to input mixer)

dc < 100 mA damage level

Input attenuator 0 to 70 dB in 10 dB steps

SWR (typical) Tune frequency

Input attenuation 10O Hz to 2.5 GHz 2.5 GHz to 5.8 GHz 5.8 GHz to 22 GHz

10 dB 1.2 1.5 1.9

0 dB

2.3 3.0 3.0

Outputs

Calibrator (front panel)

100 MHz ± (frequency reference error x 100 MHz)

-10 dBm ± 0.3 dB; 50 ohm impedance, nominal

1st LO (front panel)

2.3 to 6.1 GHz; > +5 dBm;

50 ohm impedance, nominal

Sweep and tune output (rear panel)

-1 V/GHz of tuned frequency ± (2% + 10 mV)

10 kohm impedance, nominal

Display outputs (typical parameters)

X, Y, and Z outputs for auxiliary CRT displays.

X, Y 1V for full deflection

Z 0 to 1 V intensity modulation, -1 V blank

BLANK TTL level > 2.4 V for blanking

Compatible with most oscilloscopes.

Recorder outputs (typical parameters)

Outputs to drive all current X-Y recorders using positive pencoils or TTL pen uplift.

Horizontal sweep output (X-axis)

A voltage proportional to the horizontal sweep of the frequency sweep generator. 0 V

for left edge, +10 V for right edge; 1.7 kohm impedance, nominal.

Video output (Y-axis)

Detected video output (before A-D conversion) proportional to vertical deflection of the

CRT trace 100 mV/div from 0 to 1 V; < 475 ohm impedance, nominal

Penlift output (Z-axis)

During sweep, pen down 0 V from 10 ohm source

During retrace, pen up +15 V from 10 kohm source

21.4 MHz output (rear panel, typical)

21.4 MHz; 50 ohm impedance, nominal: -20 dBm for a signal at reference level. In log

scales, the IF output logarithmically related to RF input signal; in linear, the output is

linearly related.

Frequency reference (rear panel, typical)

10.000 MHz, 0 dBm; 50 ohm output impedance

10 MHz output (rear panel, typical)

≥ 5 dBm to ohm output impedance

Video output 0 to 2 V, > 10 ohm output impedance

Display

Cathode ray tube Post deflection accelerator, aluminized P31 phosphor, electrostatic

focus and deflection.

Viewing area Approximately 9.6 cm vertically by 11.9 cm horizontally (3.8 in x 4.7 in)

1. When tuned to within ±3 MHz of signal

Specifications (continued)

1 2 ... 9 10 11 12 13 14 15 16

Comentarios a estos manuales

Sin comentarios

Agilent Technologies HP 8566B Manual de usuario Pagina 14

Comentarios a estos manuales

Relacionado con productos y manuales para De medición, control y control Agilent Technologies HP 8566B