Agilent Technologies B2201A Guía de usuario Pagina 38
- Pagina / 230
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
2-2 Agilent B2200 User’s Guide, Edition 4
Installation
This chapter describes requirements to install Agilent B2200 and the tasks for
installation, and is organized into the following three sections:
• “Requirements”
• “Inspection”
• “Installing the B2200”
• “Self-Test”
• “Output Connections”
• “Input Connections”
• “Measurement Cable Length”
• “Maintenance”
WARNING The maximum input voltage of the Agilent B2200 is ±200 V. And dangerous
voltages may be present at the output terminals. To prevent electric shock, you
must observe the following safety precautions when using the Agilent B2200.
• Use a three-conductor ac power cable to connect cabinet (if used) and the
Agilent B2200 to an electric ground (safety ground).
• If you need to touch the force and guard terminals of the output connector,
turn off the Agilent B2200 and discharge any capacitors whenever possible.
• Warn workers around the B2200 about dangerous conditions.
- Agilent B2200A 1
- Agilent B2201A 1
- Manual Part Number 2
- Warranty 2
- Technology Licenses 2
- Restricted Rights Legend 2
- Safety Summary 6
- Safety Symbols 8
- In This Manual 9
- Contents 11
- 1 Introduction 19
- Agilent B2200 Series 21
- Front Panel 22
- Introduction 23
- Figure 1-1 Front Panel View 23
- Rear Panel 24
- Figure 1-2 Rear Panel View 25
- Switch Modules 26
- Specifications 28
- General Specifications 29
- Accessories and Options 33
- 2 Installation 37
- Requirements 39
- Installation 40
- Operating Environment 41
- Inspection 42
- Installing the B2200 43
- To Set the GPIB Address 44
- To Connect the GPIB Cable 44
- To Install the Switch Module 45
- To Install the Blank Panel 45
- Self-Test 46
- Output Connections 47
- Connector Plates 48
- To Install Interlock Circuit 51
- To Install LED Circuit 52
- Cathode(-) 53
- Anode(+) 53
- To Mount Connectors 54
- 2 − ∅11.3 ∅3.2 2 − M3 x 0.5 55
- 14 11 11 14 55
- Input Connections 56
- Measurement Cable Length 59
- Maintenance 61
- 3 Front Panel Operation 63
- Operation 65
- To Initialize Agilent B2200 66
- To Enable Light Pen 66
- To Change Connection Rule 67
- To Change Connection Sequence 67
- To Control Switch Condition 67
- To save the setup 68
- To load the setup 68
- To Use Bias Mode 69
- To Use Ground Mode 70
- To Use Couple Mode 71
- To Display Firmware Revision 71
- To Display Module Information 71
- To clear error buffer 72
- LED matrix 73
- Switch Control Functions 74
- Channel Configuration Mode 75
- Connection Rule 76
- Connection Sequence 77
- Bias Mode 78
- Ground Mode 80
- Couple Mode 82
- Display Functions 84
- SequenceRule 85
- GndLock Error GndBias 85
- Card Selection key 86
- Function Edit 87
- Function key group 88
- Break_Before_Make 89
- Settings: 01 [ ] 89
- SET VIEW 90
- ENABLE DISABLE 90
- Channel: 01 90
- Channel: No Channel 90
- Channel 01: ENABLED 90
- Setup Menus 92
- Selftest Menu 96
- Enter key 97
- Exit key to return to the 97
- 4 Programming 101
- :ROUT:CONN:RULE ALL,FREE 103
- :ROUT:CONN:SEQ ALL,BBM 103
- Fundamental Commands 104
- Switch Control 105
- Programming Examples 107
- Connecting Input-Output Paths 108
- Using Bias Mode 110
- Using Ground Mode 112
- Using Couple Mode 114
- Saving Input/Output Labels 116
- Capacitance Compensation 120
- Required Conditions 121
- FORCE or SENSE (A) 126
- FORCE or SENSE (B) 126
- Insulator 126
- Triaxial Cable 126
- 5 SCPI Command Reference 129
- Common Commands 132
- Subsystem Commands 141
- SCPI Command Reference 142
- Command Summary 142
- Relay Control Commands 142
- Command Description 142
- Bias Mode Commands 143
- Ground Mode Commands 144
- Couple Mode Commands 145
- :DIAGnostic:TEST:CARD:CLEar 149
- :DIAGnostic:TEST:CARD:STATe? 149
- :DIAGnostic:TEST:FRAMe:CLEar 150
- ENTER @Agb2200;A$ 153
- [:ROUTe]:AGND:PORT 154
- [:ROUTe]:AGND[:STATe] 155
- [:ROUTe]:AGND:UNUSED 156
- [:ROUTe]:BIAS:PORT 159
- [:ROUTe]:BIAS[:STATe] 160
- [:ROUTe]:CLOSe:CARD? 161
- [:ROUTe]:CLOSe[:LIST] 161
- [:ROUTe]:CONNection:RULE 162
- [:ROUTe]:CONNection:SEQuence 162
- [:ROUTe]:COUPle:PORT 163
- [:ROUTe]:COUPle:PORT:DETect 164
- [:ROUTe]:COUPle[:STATe] 165
- [:ROUTe]:FUNCtion 166
- [:ROUTe]:OPEN:CARD 166
- [:ROUTe]:OPEN[:LIST] 167
- [:ROUTe]:SYMBol:CHANnel 167
- [:ROUTe]:SYMBol:PORT 168
- :SYSTem:BEEP 169
- :SYSTem:CCONfig? 169
- :SYSTem:CDEScription? 170
- :SYSTem:CPON 171
- :SYSTem:CTYPe? 172
- :SYSTem:DISPlay:LCD 172
- :SYSTem:DISPlay:LED 173
- :SYSTem:DISPlay:STRing 173
- :SYSTem:ERRor? 174
- :SYSTem:KLC 174
- :SYSTem:MEMOry:COMMent 175
- :SYSTem:MEMOry:DELete 175
- :SYSTem:MEMOry:LOAD 176
- :SYSTem:MEMOry:SAVE 176
- :SYSTem:PEN 177
- :SYSTem:VERSion? 177
- Status Reporting Structure 178
- Status Byte Register 180
- Output Queue 185
- 6 VXIplug&play Driver 187
- System Requirements 189
- Driver Functions 191
- VXIplug&play Driver 216
- 7 Error Messages 217
- Standard SCPI Error Messages 219
- Execution Error 223
- Device-Dependent Errors 224
- Query Errors 225
- B2200 Channel Related Errors 227
Relacionado con productos y manuales para Multímetros Agilent Technologies B2201A
Multímetros Agilent Technologies 8481B Especificaciones
(154 paginas)
(154 paginas)
(164 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.025 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales