Agilent Technologies U1251B Manual de servicio Pagina 170
- Pagina / 193
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Performance Tests and Calibration 6
Agilent U1251B/U1252B User’s and Service Guide 150
Finishing the Adjustment
1 Remove all the shorting plugs and connectors from the
instrument.
2 Record the new Calibration Count.
3 Press and simultaneously to exit the
Adjustment Mode. Power off and on again. The instrument
will then be secured.
To Read the Calibration Count
You can query the instrument to determine how many
calibrations have been performed.
When you receive your instrument, read the count to
determine its initial value.
The count value increases by one for each calibration point,
and a complete calibration will increase the value by many
counts. The calibration count increments up to a maximum
of 65535 after which it is set at 0. The calibration count can
be read from the front panel after the instrument has been
unsecured. Use the following procedure to read the
calibration count from the front panel.
Notes for adjustment table:
1 Be sure to recalibrate “Short” using the dual banana plug with copper wire after performing calibration for resistance.
2 Ensure the multimeter is turned on and stabilized for at least 60 minutes, with the K-type thermocouple connected
between the multimeter and the calibrator output terminal.
NOTE
Your instrument was calibrated before it left the factory.
- Agilent U1251B and 1
- U1252B Handheld Digital 1
- Multimeter 1
- Safety Symbols 3
- Safety Information 4
- General Safety Information 4
- Regulatory Markings 6
- 2002/96/EC 7
- In This Guide… 8
- Contents 11
- 3 Functions and Features 12
- 7 Specifications 14
- List of Figures 17
- List of Tables 19
- Getting Started 21
- °C compensation 22
- Check the shipment 23
- Adjusting the tilt-stand 24
- The front panel at a glance 26
- The rear panel at a glance 27
- The rotary switch at a glance 28
- The keypad at a glance 29
- 1 Getting Started Tutorial 30
- The display at a glance 31
- Getting Started Tutorial 1 33
- for U1251B 40
- The terminals at a glance 42
- Making Measurements 43
- Measuring Voltage 44
- Measuring AC voltage 45
- Measuring DC voltage 46
- Making Measurements 2 47
- Measuring Current 49
- Red Lead 50
- Black Lead 50
- 2 Making Measurements 50
- A (ampere) measurement 53
- Frequency Counter 54
- Audible continuity 58
- Conductance 58
- Testin g Diodes 60
- Measuring Capacitance 63
- Measuring Temperature 65
- Overload alert 69
- Input warning 69
- Charge terminal alert 70
- Functions and Features 71
- Dynamic Recording 72
- Data Hold (Trigger Hold) 74
- Refresh Hold 75
- Null (Relative) 77
- Decibel Display 79
- 1 ms Peak Hold 81
- Press for > 1 sec 82
- Data Logging 83
- Interval logging 85
- Reviewing logged data 87
- Remote Communication 93
- 3 Features and Functions 94
- Changing The Default Setting 95
- Selecting Setup Mode 96
- Setting Data Logging Mode 101
- Setting Temperature Unit 105
- Setting Beep Frequency 110
- Setting Backlight Timer 111
- Setting Baud Rate 112
- Setting Parity Check 113
- Setting Data Bit 114
- Setting Echo Mode 115
- Setting Print Mode 116
- Setting the Battery Voltage 118
- Setting the Filter 119
- Table 4-2 Filter defaults 120
- Maintenance 121
- Introduction 122
- Storage considerations 124
- Charging the battery 125
- 5 Maintenance 128
- Figure 5-3 Self-test 128
- Table 5-2 Error messages 128
- and appear to 130
- Maintenance 5 131
- Fuse checking procedure 132
- Displayed readings 133
- 1 440 mA/1000 V 6.2 MΩ OL 133
- 2 11 A/1000 V 0.06 Ω OL 133
- Replacing the fuse 134
- Troubleshooting 136
- Replaceable Parts 137
- Agilent Technologies 139
- Calibration Overview 140
- Calibration interval 141
- Adjustment is recommended 141
- Recommended Test Equipment 142
- Basic Operating Test 143
- Current terminal test 144
- Charge terminal alert test 145
- Test Considerations 146
- Calibration Security 147
- Error from nominal 1 year 151
- U1251B U1252B 151
- ± 350 mW 152
- Calibration Process 159
- Selecting the Adjustment Mode 160
- Entering Adjustment Values 160
- Adjustments Consideration 161
- Adjustment Procedure 163
- position 166
- Finishing the Adjustment 170
- Calibration Errors 171
- Specifications 173
- Product Characteristics 174
- Specifications 7 175
- Measurement Category 177
- Specification Assumptions 178
- Electrical Specifications 178
- ≤ reading ≤ 0.8 V) 180
- AC Specifications 181
- AC specifications for U1252B 182
- Capacitance Specifications 184
- Temperature Specifications 184
- Frequency Specifications 185
- For voltage measurements 186
- For current measurements 187
- Peak Hold Specifications 188
- [2][4][5] 189
- [2][4][6] 189
- Operating Specifications 191
- Input impedance 192
Relacionado con productos y manuales para Multímetros Agilent Technologies U1251B
Multímetros Agilent Technologies 6002A Guía de usuario
(320 paginas)
(320 paginas)
Multímetros Agilent Technologies B2902 Guía de usuario
(232 paginas)
(232 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.061 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales