Agilent Technologies 54501A Especificaciones Pagina 20
- Pagina / 168
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
85330A Multiple Channel Controller 1-1
Installation
1 Installation
Installation at a
Glance
The installation procedure is composed of the following basic steps:
1. If you just purchased an antenna measurement system, install all
components as described in the documentation that came with that
system. Do not connect the Agilent 85330A yet.
2. Turn on the system and perform a functional check.
3. If desired, verify the performance of the system components by referring
to the Performance Verification chapter of the system manual.
4. Install and verify the 85330A system as explained in this manual.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
- 1
- Agilent Technologies 85330A 2
- Multiple Channel Controller 2
- Restricted Rights Legend 3
- Warranty 5
- Service and Support 6
- Instrument Markings 7
- Safety Earth 8
- Manufacturers Declaration 10
- DECLARATION OF CONFORMITY 11
- Typeface Conventions 12
- Contents 14
- 1 Installation 20
- Choosing the Proper 21
- Installation 22
- Controller 25
- Procedure 26
- Triggers 27
- • SCU address is set to 0 29
- 2 Performance Verification 32
- Recommended 33
- Equipment 33
- Performance Verification Test 34
- Setting Up the Equipment 34
- {Coupling: DC} 35
- Measurement Display 36
- Performance Verification 37
- Pulse Receive and 39
- Cycle Test 39
- Counter Pulse Delay 40
- 12. Remove the BNC cables 41
- Width Test 42
- Measurement Busy 42
- Signal and Pulse 42
- Verifying the RF Switches 44
- • Jumper (see below) 46
- • Soldering iron 46
- • 2 jumper wires 46
- AUX 1 and AUX 2 48
- Output Voltage Test 49
- When Finished with 49
- All Tests 49
- 3 Operator’s Check 50
- Operator’s Check 51
- 4 General Information 52
- Measurement Speed Advantages 53
- Triggering 53
- • Perform service functions 54
- Switch control units 55
- The Downloadable 56
- • Option 001: 1 meter 57
- • Option 002: 2 meters 57
- • Option 005: 5 meters 57
- • Option 010: 10 meters 57
- • A switch control unit (SCU) 58
- General Information 59
- Characteristics 60
- Ventilation 61
- Requirements 61
- Dimensions 61
- Need More 62
- Information 62
- Rear Panel Features 63
- SWITCH PORT 1 and 2 65
- AUX POWER IN 65
- 85330A Compatibility 66
- 5 Manual Operation 68
- To Use the Front Panel 69
- Softkey Map 70
- Changing the GPIB 71
- (to select a channel) 72
- Manual Operation 73
- To Perform Service Functions 74
- 6 Programming 76
- Definition of Terms 77
- • CW Measurement Configuration 78
- • 8530A Control of Sources 78
- • Fast Source Control 78
- CW Measurement Configuration 79
- To Use this 80
- 85330A settings 81
- 8530A Control of Sources 82
- Fast Source Control 83
- To Use Direct Control 84
- In this example: 86
- To Use Run-Time Control Mode 87
- TTL Trigger and 88
- Ready Timeouts 88
- Select Switch State 89
- Event Trigger 90
- Receiver Ready 90
- Switch List Loop 90
- Frequency Loop 92
- Event Loop 92
- Programming 100
- Programming Examples 100
- 85330A Error Messages 109
- 7 Remote Programming Command 112
- Abbreviated Commands 113
- Parameters 113
- Common Commands 114
- Syntax *OPC? 115
- Syntax *RST 115
- Example OUTPUT 70918;”*RST” 115
- Standard Command Reference 116
- ROUTe:CLOSe 116
- ROUTe:CONTrol 117
- ROUTe:DELay 117
- Subsystem Command Syntax 118
- :INITiate 118
- :TIMEout 118
- RUNTime:CONTroller 119
- RUNTime:EVENt:COUNt 119
- RUNTime:EVENt:TRIGger 120
- RUNTime:INITiate:IMM 121
- RUNTime:SOURce:COUNt 121
- RUNTime:SWITch:DELay 123
- RUNTime:SWITch:SCAN 124
- RUNTime:SWITch:TRIGger 125
- RUNTime:TIMEout:EVENt 126
- RUNTime:TIMEout:RECeiver 126
- RUNTime:TIMEout:REMote 127
- RUNTime:TIMEout:SOURce 127
- SYSTem:ERRor? 128
- 8 In Case of Difficulty 130
- In Case of Difficulty 131
- 9 Service 132
- Theory of Operation 133
- GPIB 134
- Recommended Test Equipment 138
- Troubleshooting 140
- 85383A Local Control Cable 142
- 85383B Expansion Cable 142
- 85384A Switch Driver Cable 142
- 85385A Remote Trigger Cable 142
- Table 9-5 85385A Wiring 143
- Replaceable Parts 144
- Mainframe, Plug-in 146
- Switch Control Unit 147
- RF Switch 147
- Interconnect Cables 148
- Assembly and Disassembly 149
- E1330 Card 150
- Configuration 150
- 85330-60002 Card 150
- Disassembly 151
- Assembly 151
- Adjustments 152
- Selecting the Multiple 153
- Channel Controller’s 153
- GPIB Address 153
- Switching from the 154
- Internal to External 154
- Power Supply 154
- Preventive Maintenance 155
- 10 Accessory Documentation 157
- Accessory Documentation 158
- A Glossary 159
- • Attaching cables 160
- Glossary 161
- Standard System 163
- Switch Address 163
- Switch Module 163
- Numerics 165
© 2020, manymanuals.es. Todos los derechos reservados | 0.057 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales