Agilent Technologies E1465A Manual de usuario Pagina 57
- Pagina / 105
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Matrix Modules Command Reference 57Chapter 4
INITiate
The INITiate command subsystem selects continuous scanning cycles and
starts the scanning cycle.
Subsystem Syntax INITiate
:CONTinuous <mode>
:CONTinuous?
[:IMMediate]
INITiate:CONTinuous
INITiate:CONTinuous <mode> enables or disables continuous scanning
cycles for the matrix modules.
Parameters
Comments Continuous Scanning Operation: Continuous scanning is enabled with
INITiate:CONTinuous ON or INITiate:CONTinuous 1. Sending
INITiate:IMMediate closes the first channel in the channel list. Each trigger
from the source specified by TRIGger:SOURce advances the scan through
the channel list. A trigger at the end of the channel list closes the first
channel in the channel list and the scan cycle repeats.
Noncontinuous Scanning Operation: Noncontinuous scanning is enabled
with INITiate:CONTinuous OFF or INITiate:CONTinuous 0. Sending
INITiate:IMMediate closes the first channel in the channel list. Each trigger
from the source specified by TRIGger:SOURce advances the scan through
the channel list. At the end of the scanning cycle, the last channel in the
channel list is opened.
Stopping Continuous Scan: See the ABORt command.
Related Commands: ABORt, ARM:COUNt, TRIGger:SOURce
*RST Condition: INITiate:CONTinuous OFF | 0
Name Type Range of Values Default Value
<mode>boolean
ON | OFF | 1 | 0 OFF | 0
- Agilent Technologies 1
- E1465A/E1466A/E1467A 1
- Relay Matrix Switch Modules 1
- User’s Manual 1
- Contents 3
- Safety Symbols 8
- WARNINGS 8
- Documentation History 8
- DECLARATION OF CONFORMITY 9
- Getting Started 11
- TERMINAL MODULEMATRIX MODULE 12
- Addressing the 15
- Example: Closing 16
- Relays (BASIC) 16
- Relays (Turbo C) 17
- Chapter 2 19
- Using This Chapter 19
- WARNINGS and CAUTIONS 19
- Configuring the Switch Module 20
- Setting the Logical 21
- Address Switch 21
- Setting the Interrupt 21
- Installing the 23
- Switch Module in a 23
- Mainframe 23
- • Terminal Module Connectors 24
- • Wiring Terminal Modules 24
- Terminal Module 24
- Connectors 24
- Daisy Chain Rows 26
- Rows (00-07) 26
- Columns (00-15) 26
- Columns (16-31) 26
- Wiring the Terminal 27
- Attaching the 29
- Terminal Modules 29
- Configuring Larger Matrixes 30
- E1465A TERMINAL MODULES 31
- Creating a 4x256 32
- Creating an 8x96 33
- Creating Larger 34
- Matrixes with 34
- Multiple Mainframes 34
- Using the Matrix Modules 35
- Example: Matrix 36
- Identification 36
- (TURBO C) 37
- Switching Channels 38
- Scanning Channels 39
- Example: Scanning 41
- Using Trig In/Out 41
- Ports (BASIC) 41
- Querying Matrix Modules 42
- Using the Scan Complete Bit 42
- Example: Using the 43
- Scan Complete Bit 43
- Saving and Recalling States 44
- Detecting Error Conditions 45
- Synchronizing Matrix Modules 46
- Understanding Matrix Modules 47
- Chapter 4 49
- Command Types 49
- SCPI Command Reference 51
- Subsystem Syntax ABORt 52
- ARM:COUNt 53
- ARM:COUNt? 54
- DISPlay:MONitor:CARD 55
- DISPlay:MONitor[:STATe] 56
- INITiate 57
- INITiate:CONTinuous? 58
- INITiate[:IMMediate] 58
- OUTPut:EXTernal[:STATe] 59
- OUTPut:EXTernal[:STATe]? 60
- OUTPut[:STATe] 60
- OUTPut[:STATe]? 61
- OUTPut:TTLTrgn[:STATe] 61
- OUTPut:TTLTrgn[:STATe]? 62
- [ROUTe:] 63
- [ROUTe:]CLOSe? 64
- Parameters 65
- Comments Opening Channels: 65
- [ROUTe:]OPEN? 66
- [ROUTe:]SCAN 66
- Subsystem Syntax STATus 68
- Output Queue 69
- Status Byte Register 69
- OPERation Status Register 69
- STATus:OPERation:CONDition? 70
- STATus:OPERation:ENABle 70
- STATus:OPERation:ENABle? 70
- STATus:OPERation[:EVENt]? 71
- STATus:PRESet 71
- SYSTem:CDEScription? 72
- SYSTem:CPON 73
- SYSTem:CTYPe? 73
- SYSTem:ERRor? 74
- TRIGger[:IMMediate] 75
- TRIGger:SOURce 76
- TRIGger:SOURce? 77
- SCPI Commands Quick Reference 78
- Matrix Modules Specifications 81
- Register-Based Programming 83
- Register Descriptions 86
- Reading the 87
- Status/Control Register 87
- Writing to the 87
- Relay Control 88
- Register 88
- Programming Examples 90
- Example: Reading 91
- (C/HP-UX) 91
- Example: Making 92
- Measurements 92
- Channels (BASIC) 95
- Channels (C/HP-UX) 96
- Matrix Modules Error Messages 99
- Error Messages 100
- Relay Life 101
- R (continued) 105
© 2020, manymanuals.es. Todos los derechos reservados | 0.043 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales