Agilent-technologies E1300B Manual de usuario Pagina 176
- Pagina / 244
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
:COMMunicate
:SERial[n]:TRANsmit
:PACE [:PROTocol]
SYSTem:COMMunicate:SERial[n]:TRANsmit:PACE[:PROTocol]
< protocol> enables or disables the transmit pacing (XON/XOFF) protocol.
Parameters Parameter
Name
Parameter
Type
Range of
Values
Default
Units
protocol discrete XON| NONE none
Comments • For an Agilent E1324A, AUTO is always ON. In this case
…TRAN:PACE will also set …[RECeive]:PACE
• Receipt of an XOFF character (ASCII 19
10
, 13
16
) will hold off
transmission of data until an XON character (ASCII 17
10
, 11
16
) is
received.
• DIAG:BOOT:COLD will set …PACE to XON.
• Related Commands: SYST:COMM:SER[n]:TRAN:AUTo
• *RST Condition: No change
Example Set XON/XOFF transmit pacing
SYST:COMM:SER0:TRAN:PACE:PROT XON
:COMMunicate
:SERial[n] :TRANsmit
:PACE [:PROTocol]?
SYSTem:COMMunicate:SERial[n]:TRANsmit:PACE[:PROTocol]? returns
the current transmit pacing protocol.
Example Check transmit pacing protocol
SYST:COMM:SER0:TRAN:PACE:PROT?
enter statement statement enters the string
"X O N " or "N ON E "
:DATE SYSTem:DATE < year>,<month>,<day> sets the E1300/E1301
mainframe’s internal calendar.
Parameters Parameter
Name
Parameter
Type
Range of
Values
Default
Units
year numeric must round to 1980 to 2079 none
month numeric must round to 1 to 12 none
day numeric must round to
1 through last day of month
none
Comments • The upper limit on the day parameter is dependent on the month
parameter and may be dependent on the year parameter in the case of a
leap year.
SYSTem:COMMunicate :SERial[n]:TRANsmit :PACE [:PROTocol]
7-48 System Instrument Command Reference
- 75000 SERIES B 1
- Mainframes 1
- E1300B and E1301B 1
- Multimeter User’s Manual 6
- About this Manual 8
- Table of Contents 9
- 6 - Table of Contents 14
- Getting Started 15
- Instrument 17
- Definition 17
- Introductory 18
- Programming 18
- Examples 18
- 1-6 Getting Started 20
- Using the Front Panel 21
- A 60-Second Menu 22
- Tutorial 22
- Using the System 23
- Instrument Menu 23
- How to Reset the System 24
- Using the Other 25
- Instrument Menus 25
- How to Open/Close Channels 26
- How to Scan Channels 26
- How to Select Monitor Mode 27
- Executing 29
- Menu Keys 30
- Display Control & 30
- Editing Keys 30
- Instrument Control 31
- Other Keys 31
- In Case of Difficulty 32
- System Instrument Menu 34
- Switchbox Menu 36
- Using the Front Panel 2-17 37
- Scanning Voltmeter Menu 38
- Using the Front Panel 2-23 43
- Counter Menu 46
- 2-28 Using the Front Panel 48
- Chapter 3 49
- Terminal Interface 50
- Features 50
- General Key 62
- Descriptions 62
- Using Supported 64
- Terminals 64
- Using Other 67
- What “Not Supported” 68
- Testing Terminals for 68
- Compatibility 68
- Using a Terminal 69
- Without Menus 69
- Using the Mainframe 89
- Mainframe Data 94
- Non-Volatile User 95
- Downloading Device Drivers 99
- GPIB bus 100
- Configuration 101
- Download Program 102
- Downloading 104
- Drivers in MS-DOS 104
- Systems with 105
- Drivers in GPIB 105
- Systems with BASIC 106
- Multiple Drivers 107
- Checking Driver 107
- Manually 108
- Downloading a 108
- Driverdown manual 108
- Manually Downloading 109
- Over GPIB 109
- Over RS-232 109
- Chapter 6 115
- Status System 116
- Structure 116
- The Status Byte 117
- Register 117
- Reading the Status 118
- Byte Register 118
- Standard Event Status 120
- Unmasking Standard 120
- Event Status Bits 120
- Reading the 122
- Condition Register 122
- Unmasking the 122
- Operation Event 122
- Register Bits 122
- Clearing the Operation 123
- Event Register Bits 123
- Using the Operation 123
- Status Group Registers 123
- Interrupting an 124
- External Computer 124
- Synchronizing an 126
- Chapter 7 129
- SCPI Command 132
- Reference 132
- :COMMunicate 135
- :SERial[0][:OWNer] 135
- :SERial[0][:OWNer]? 136
- :SERial[n]:STORe 136
- :DOWNload:CHECked 137
- [:MADDress] 137
- :SADDress 139
- :DOWNload 141
- :DRIVer:LOAD 145
- < driver_block> 145
- :DRIVer :LOAD: 145
- :OPERation 160
- :CONDition? 160
- :OPERation:ENABle 160
- <event> 160
- :SERial[n] :CONTrol 165
- :CONFigure 182
- :DLADdress? 182
- ADDR 0" 184
- :HIERarchy? 185
- :HIERarchy:ALL? 186
- :INFormation? 186
- GPIB Message 200
- Device Clear (DCL) or 201
- Selected Device Clear 201
- Command Quick 203
- SCPI Commands Quick Reference 204
- Command Description 204
- System Instrument 204
- Specifications 209
- SCPI Conformance 211
- Information 211
- A-4 Specifications 212
- Specifications A-5 213
- A-6 Specifications 214
- Specifications A-7 215
- D/A Converter 216
- Commands 216
- Specifications A-9 217
- Specifications A-11 219
- A-12 Specifications 220
- Error Messages 221
- Error Messages B-3 223
- Error Messages and Causes 223
- Code Message Cause 223
- B-4 Error Messages 224
- Start-up Error 225
- Messages 225
- B-6 Error Messages 226
- Connecting and Configuring a 227
- Display Terminal 227
- Agilent 24542H 228
- Configuring a 229
- Terminal for the 229
- Mainframe 229
- Configuring the 230
- Mainframe with 230
- Appendix D 233
- Sending Binary 234
- Data Over RS-232 234
Relacionado con productos y manuales para Hardware Agilent-technologies E1300B
Hardware Agilent-technologies E5810A Manual de usuario
(159 paginas)
(159 paginas)
Hardware Agilent-technologies J3972A Manual de usuario
(189 paginas)
(189 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.051 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales