Agilent Technologies 77-4 Guía de usuario Pagina 195
- Pagina / 224
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
ESG Family Signal Generators Hardkey and Softkey Reference
Utility
User’s Guide 4-139
Transmit Pace None Xon
This softkey in the RS-232 Pace menu determines whether any pacing
is acknowledged by the RS-232 transmit channel. If Xon pacing is us ed,
the system will suspend transmitting data upon receiving an Xoff
character until an Xon character is received. The signal generator may
not be responsive to other channels, or to the front panel, while
transmission is suspended. Xon pacing is not recommended if binary
data will be sent to the signal generator via RS-232. Toggle
Transmit Pace None Xon to None to turn off Xon pacing.
Pace is a persistent state; it is not affected by an instrument preset or
by a power cycle.
Softkey Location:
Utility > GPIB/RS-232 > RS-232 Pace >
Transmit Pace None Xon
Update in Remote Off On
This softkey toggles between the display updating off or on, when the
remote control bus is in remote.
This is a persistent state in the preset mode. However, it resets to off,
the default value, when the power is cycled.
Softkey Location:
Utility > Display > Update in Remote
UWCDMA
Pres s this so ftkey to set the curr ent cata log typ e to UWC DMA a nd
display the catalog of UWCDMA files.
Softkey Location:
Utility > Memory Catalog > Catalog Type >
ARB Catalog Types > UWCDMA
View Next Error Message
If the ERR annunciator is turned on in the display, you have at least one
error message stored in the error message queue. Use this softkey to
display the first error message in the queue. (The first error message is
the oldest error.) There may be more than one error message in the
queue; the number of error mess ages is displayed along with the first
message. If there is more than one message, continue pressing this
softkey to view the rest of the error messages. If you wish to back up
and view a message you have already seen, press
View Previous Error Message. Press any front panel key to remove the error
message from the display and return to normal signal generator
operation.
- Agilent Technologies 1
- ESG Family Signal Generators 1
- Contents 3
- 1Preparing for Use 5
- Checking the Shipment 6
- Line Settings 7
- Ventilation 8
- Environment 8
- Proper Usage and Cleaning 8
- Selecting Inverse Video 9
- Adjusting the Screen Saver 9
- Operator’s Check 11
- User’s Guide 1-9 13
- User’s Guide 14
- 2Using Functions 15
- To Set the RF Frequency 16
- Modulation 19
- Setting the AM Rate 20
- Setting the FM Rate 22
- Configuring a Step Sweep 23
- Editing List Sweep Points 24
- Enabling Options 27
- Enabling a Software Option 29
- If You Encounter a Problem 30
- Can’t Turn Off Help Mode? 32
- R annunciator will be 33
- Table 2-1 Contacting Agilent 35
- 3Front and Rear Panel 37
- Front Panel Overview 38
- 34. PULSE IN Connector 43
- Display Annotation 44
- 5. Text Area 45
- 6. Active Entry Area 45
- 7. Annunciators 45
- Utility menu 46
- User’s Guide 3-11 47
- Rear Panel Overview 48
- 1. AC Power Receptacle 49
- 2. GPIB Connector 49
- 3. SYMBOL SYNC OUT Connector 49
- 12. PATTERN TRIG IN Connector 51
- 13. BURST GATE IN Connector 51
- 15. ALT PWR IN Connector 51
- 16. EVENT 1 Connector 52
- 17. EVENT 2 Connector 52
- 19. I OUT Connector 53
- 20. Q OUT Connector 54
- 21. BER MEAS END Connector 54
- 22. BER TEST OUT Connector 54
- 23. BER ERR OUT Connector 54
- 24. BER NO DATA Connector 54
- 25. BER SYNC LOSS Connector 55
- 26. BER DATA IN Connector 55
- 27. BER CLK IN Connector 55
- 28. BER GATE IN Connector 55
- 29. 321.4 MHz IN Connector 55
- Hardkey and Softkey Reference 57
- AM Depth 58
- AM Depth Couple Off On 58
- AM Off On 59
- AM Path 1 2 WB 59
- AM Source 60
- AM Start Rate 61
- AM Stop Rate 61
- AM Sweep Time 62
- AM Sweep Trigger 62
- AM Tone 1 Rate 62
- AM Tone 2 Rate 63
- AM Waveform 63
- ALC BW Normal Narrow 69
- ALC Off On 70
- User’s Guide 4-15 71
- Ampl Offset 72
- Ampl Ref Set 72
- Ampl Ref Off On 72
- Atten Hold Off On 73
- Power Search 74
- Amplitude 75
- Arrow Keys 76
- Display Contrast Keys 77
- DCFM/DCΦM Cal 78
- FM Dev Couple Off On 81
- FM Off On 82
- FM Path 1 2 82
- FM Source 83
- FM Start Rate 84
- FM Stop Rate 84
- FM Sweep Time 84
- FM Sweep Trigger 85
- FM Tone 1 Rate 85
- FM Tone 2 Rate 86
- FM Waveform 86
- Adjust Phase 90
- Freq Multiplier 91
- Freq Offset 91
- Freq Ref Off On 92
- Freq Ref Set 92
- Optimize 93
- Phase Ref Set 93
- Frequency 94
- 4-40 User’s Guide 96
- Incr Set 97
- Burst Envelope Off On 99
- Burst Source 99
- Calibration Type User Full 100
- Do Power Search 100
- Execute Cal 100
- High Crest Mode Off On 101
- I/Q Calibration 102
- I Offset 102
- I/Q Adjustments 102
- I/Q Adjustments Off On 102
- I/Q Gain 103
- I/Q Off On 103
- I/Q Source 103
- Int Burst 104
- Power Search Manual Auto 104
- Q Offset 105
- Quadrature Skew 105
- Start Frequency 106
- Stop Frequency 106
- Dual-Sine 108
- Function Generator 108
- Immediate 108
- Internal Modulation 109
- LF Out Amplitude 109
- LF Out Freq 109
- LF Out Off On 110
- LF Out Period 110
- LF Out Source 111
- LF Out Start Freq 111
- LF Out Stop Freq 112
- LF Out Sweep Time 112
- LF Out Sweep Trigger 113
- LF Out Tone 1 Freq 113
- LF Out Tone 2 Ampl % Of Peak 114
- LF Out Tone 2 Freq 114
- LF Out Waveform 115
- LF Out Width 115
- 4-60 User’s Guide 116
- Swept-Sine 117
- Triangle 117
- Trigger In Polarity Neg Pos 117
- Trigger Key 118
- Trigger Out Polarity Neg Pos 118
- User’s Guide 4-63 119
- Mod On/Off 120
- User’s Guide 4-65 121
- Numeric Keypad 122
- Phase Modulation 123
- M Dev Couple Off On 125
- M Off On 125
- 4-70 User’s Guide 126
- M Source 127
- ΦM Start Rate 127
- M Stop Rate 128
- M Sweep Time 128
- ΦM Sweep Trigger 128
- M Tone 1 Rate 129
- M Tone 2 Ampl Percent Of Peak 129
- ΦM Tone 2 Rate 129
- 4-74 User’s Guide 130
- Ext 1 AC-Coupled 131
- Ext 1 DC-Coupled 131
- Ext 2 AC-Coupled 132
- Ext 2 DC-Coupled 132
- FM ΦM Normal High BW 132
- Internal 133
- Power Switch 136
- User’s Guide 4-81 137
- Ext2 DC-Coupled 138
- Fast Pulse Off On 138
- Internal Pulse 139
- Internal Square 139
- Pulse Off On 139
- Pulse Period 140
- Pulse Rate 140
- Pulse Source 140
- Pulse Width 141
- Delete All Regs in Seq [n] 142
- Delete All Sequences 142
- Delete Seq[n] Reg[nn] 143
- Recall Reg 143
- Select Seq 144
- RF On/Off 146
- Add Comment To Seq[n] Reg[nn] 147
- Clear Text 148
- Editing Keys 149
- Editing Mode Insert Replace 149
- Save Seq[n] Reg[nn] 150
- Select Reg 150
- Sweep/List 152
- Ampl Start 153
- Ampl Stop 153
- Configure List Sweep 153
- Delete Item 154
- Delete Row 154
- Configure Step Sweep 154
- Delete File 154
- Dwell Type List Step 155
- Edit Item 155
- Freq&Ampl 156
- Freq Start 156
- Freq Stop 156
- Goto Bottom Row 156
- Goto Middle Row 157
- Goto Row 157
- Goto Top Row 157
- Insert Item 158
- Insert Row 158
- Load From Selected File 158
- Load List From Step Sweep 159
- Load/Store 159
- Manual Mode Off On 159
- Manual Point 159
- Page Down 160
- Point Trigger 160
- Preset List 161
- Single Sweep 161
- Step Dwell 161
- Store to File 161
- Sweep Direction Down Up 162
- Sweep Repeat Single Cont 162
- Sweep Trigger 163
- Sweep Type List Step 163
- 4-110 User’s Guide 166
- ARB Catalog Types 167
- Black Pixels Screen Test 168
- Brightness 168
- Calibrate Selected Items 168
- Catalog Type 169
- Clear Error Queue(s) 169
- Copy File 170
- Delete All Files 172
- Deselect All Items 173
- Deselect Item 173
- Diagnostic Info 173
- Hardware Options 176
- Help Mode Single Cont 176
- 8648A/B/C/D 177
- 8656B,8657A/B 177
- 8657D NADC (Option UN8) 177
- 8657D PDC (Option UN8) 178
- 8657J PHS (Option UN8) 178
- GPIB Address 178
- GPIB/RS-232 179
- Installed Board Info 179
- Instrument Adjustments 179
- 4-124 User’s Guide 180
- Modify License Key 181
- Mod Status Info Off On 182
- Modulation Catalog Types 182
- Options Info 183
- Power On Last Preset 184
- Power On/Preset 184
- Preset Language 185
- Preset Normal User 185
- Proceed With Reconfiguration 185
- Recall Ref Osc Setting 186
- Receive Pace None Xon 186
- Ref Osc Coarse 186
- Ref Osc Fine 187
- Remote Language 187
- Rename File 187
- Reset RS-232 188
- RS-232 Baud Rate 189
- RS-232 Echo Off On 189
- RS-232 Pace 189
- RS-232 Timeout 189
- RTS/CTS Pacing 190
- Save User Preset 191
- Screen Saver Delay 191
- Screen Saver Mode 192
- Screen Saver Off On 192
- Select Item 192
- Software Options 193
- Step/Knob Ratio 194
- Store Ref Osc Setting 194
- Transmit Pace None Xon 195
- Update in Remote Off On 195
- View Next Error Message 195
- View Previous Error Message 196
- White Pixels Screen Test 196
- 5Memory Structure 197
- Memory Types 198
- Viewing Stored Files 199
- Copying Stored Files 200
- Renaming Stored Files 200
- Deleting Stored Files 200
- 6Safety and Regulatory 201
- Safety Notes 202
- Instrument Markings 203
- General Safety Considerations 204
- Statement of Compliance 205
- Assistance 206
- Certification 207
- Declaration of Conformity 208
- -3.GSGV Deutschland) 209
Relacionado con productos y manuales para De medición, control y control Agilent Technologies 77-4
(37 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.057 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales