Agilent Technologies 77-4 Guía de usuario Pagina 87
- Pagina / 224
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
ESG Family Signal Generators Hardkey and Softkey Reference
FM
User’s Guide 4-31
Noise
This softkey lets you specify noise as the frequency modulation
waveform for the
FM Path 1 and FM Path 2 configurations. Notice that the
selected waveform applies only to whichever FM path configuration you
have cu rren tly se lect ed.
Softkey Location:
FM/ΦM > FM Waveform > Noise
Ramp
This softkey lets you specify ramp as the frequency modulation
waveform for the
FM Path 1 and FM Path 2 configurations. Notice that the
selected waveform applies only to whichever FM path configuration you
have cu rren tly se lect ed.
Softkey Location:
FM/ΦM > FM Waveform > Ramp
Sine
This softkey lets you specify sine as the frequency modulation
waveform for the
FM Path 1 and FM Path 2 configurations. Notice that the
selected waveform applies only to whichever FM path configuration you
have cu rren tly se lect ed.
Softkey Location:
FM/ΦM > FM Waveform > Sine
Square
This softkey lets you specify square as the frequency modulation
waveform for the
FM Path 1 and FM Path 2 configurations. Notice that the
selected waveform applies only to whichever FM path configuration you
have cu rren tly se lect ed.
Softkey Location:
FM/ΦM > FM Waveform > Square
Swept-Sine
Pressing this softkey reveals a menu of choices for setting the
swept-sine frequency modulation parameters. In this menu you can set
the start and stop FM rate and the sweep time. You can set the signal
generator to a single, externally-triggered sweep on either a negative or
positive TTL level or you can choose continuous sweep, triggered
immediately. In this menu you can also s elect either a positive or
negative polarity for the TRIGGER OUT signal.
Softkey Location:
FM/ΦM > FM Waveform > Swept-Sine
- Agilent Technologies 1
- ESG Family Signal Generators 1
- Contents 3
- 1Preparing for Use 5
- Checking the Shipment 6
- Line Settings 7
- Ventilation 8
- Environment 8
- Proper Usage and Cleaning 8
- Selecting Inverse Video 9
- Adjusting the Screen Saver 9
- Operator’s Check 11
- User’s Guide 1-9 13
- User’s Guide 14
- 2Using Functions 15
- To Set the RF Frequency 16
- Modulation 19
- Setting the AM Rate 20
- Setting the FM Rate 22
- Configuring a Step Sweep 23
- Editing List Sweep Points 24
- Enabling Options 27
- Enabling a Software Option 29
- If You Encounter a Problem 30
- Can’t Turn Off Help Mode? 32
- R annunciator will be 33
- Table 2-1 Contacting Agilent 35
- 3Front and Rear Panel 37
- Front Panel Overview 38
- 34. PULSE IN Connector 43
- Display Annotation 44
- 5. Text Area 45
- 6. Active Entry Area 45
- 7. Annunciators 45
- Utility menu 46
- User’s Guide 3-11 47
- Rear Panel Overview 48
- 1. AC Power Receptacle 49
- 2. GPIB Connector 49
- 3. SYMBOL SYNC OUT Connector 49
- 12. PATTERN TRIG IN Connector 51
- 13. BURST GATE IN Connector 51
- 15. ALT PWR IN Connector 51
- 16. EVENT 1 Connector 52
- 17. EVENT 2 Connector 52
- 19. I OUT Connector 53
- 20. Q OUT Connector 54
- 21. BER MEAS END Connector 54
- 22. BER TEST OUT Connector 54
- 23. BER ERR OUT Connector 54
- 24. BER NO DATA Connector 54
- 25. BER SYNC LOSS Connector 55
- 26. BER DATA IN Connector 55
- 27. BER CLK IN Connector 55
- 28. BER GATE IN Connector 55
- 29. 321.4 MHz IN Connector 55
- Hardkey and Softkey Reference 57
- AM Depth 58
- AM Depth Couple Off On 58
- AM Off On 59
- AM Path 1 2 WB 59
- AM Source 60
- AM Start Rate 61
- AM Stop Rate 61
- AM Sweep Time 62
- AM Sweep Trigger 62
- AM Tone 1 Rate 62
- AM Tone 2 Rate 63
- AM Waveform 63
- ALC BW Normal Narrow 69
- ALC Off On 70
- User’s Guide 4-15 71
- Ampl Offset 72
- Ampl Ref Set 72
- Ampl Ref Off On 72
- Atten Hold Off On 73
- Power Search 74
- Amplitude 75
- Arrow Keys 76
- Display Contrast Keys 77
- DCFM/DCΦM Cal 78
- FM Dev Couple Off On 81
- FM Off On 82
- FM Path 1 2 82
- FM Source 83
- FM Start Rate 84
- FM Stop Rate 84
- FM Sweep Time 84
- FM Sweep Trigger 85
- FM Tone 1 Rate 85
- FM Tone 2 Rate 86
- FM Waveform 86
- Adjust Phase 90
- Freq Multiplier 91
- Freq Offset 91
- Freq Ref Off On 92
- Freq Ref Set 92
- Optimize 93
- Phase Ref Set 93
- Frequency 94
- 4-40 User’s Guide 96
- Incr Set 97
- Burst Envelope Off On 99
- Burst Source 99
- Calibration Type User Full 100
- Do Power Search 100
- Execute Cal 100
- High Crest Mode Off On 101
- I/Q Calibration 102
- I Offset 102
- I/Q Adjustments 102
- I/Q Adjustments Off On 102
- I/Q Gain 103
- I/Q Off On 103
- I/Q Source 103
- Int Burst 104
- Power Search Manual Auto 104
- Q Offset 105
- Quadrature Skew 105
- Start Frequency 106
- Stop Frequency 106
- Dual-Sine 108
- Function Generator 108
- Immediate 108
- Internal Modulation 109
- LF Out Amplitude 109
- LF Out Freq 109
- LF Out Off On 110
- LF Out Period 110
- LF Out Source 111
- LF Out Start Freq 111
- LF Out Stop Freq 112
- LF Out Sweep Time 112
- LF Out Sweep Trigger 113
- LF Out Tone 1 Freq 113
- LF Out Tone 2 Ampl % Of Peak 114
- LF Out Tone 2 Freq 114
- LF Out Waveform 115
- LF Out Width 115
- 4-60 User’s Guide 116
- Swept-Sine 117
- Triangle 117
- Trigger In Polarity Neg Pos 117
- Trigger Key 118
- Trigger Out Polarity Neg Pos 118
- User’s Guide 4-63 119
- Mod On/Off 120
- User’s Guide 4-65 121
- Numeric Keypad 122
- Phase Modulation 123
- M Dev Couple Off On 125
- M Off On 125
- 4-70 User’s Guide 126
- M Source 127
- ΦM Start Rate 127
- M Stop Rate 128
- M Sweep Time 128
- ΦM Sweep Trigger 128
- M Tone 1 Rate 129
- M Tone 2 Ampl Percent Of Peak 129
- ΦM Tone 2 Rate 129
- 4-74 User’s Guide 130
- Ext 1 AC-Coupled 131
- Ext 1 DC-Coupled 131
- Ext 2 AC-Coupled 132
- Ext 2 DC-Coupled 132
- FM ΦM Normal High BW 132
- Internal 133
- Power Switch 136
- User’s Guide 4-81 137
- Ext2 DC-Coupled 138
- Fast Pulse Off On 138
- Internal Pulse 139
- Internal Square 139
- Pulse Off On 139
- Pulse Period 140
- Pulse Rate 140
- Pulse Source 140
- Pulse Width 141
- Delete All Regs in Seq [n] 142
- Delete All Sequences 142
- Delete Seq[n] Reg[nn] 143
- Recall Reg 143
- Select Seq 144
- RF On/Off 146
- Add Comment To Seq[n] Reg[nn] 147
- Clear Text 148
- Editing Keys 149
- Editing Mode Insert Replace 149
- Save Seq[n] Reg[nn] 150
- Select Reg 150
- Sweep/List 152
- Ampl Start 153
- Ampl Stop 153
- Configure List Sweep 153
- Delete Item 154
- Delete Row 154
- Configure Step Sweep 154
- Delete File 154
- Dwell Type List Step 155
- Edit Item 155
- Freq&Ampl 156
- Freq Start 156
- Freq Stop 156
- Goto Bottom Row 156
- Goto Middle Row 157
- Goto Row 157
- Goto Top Row 157
- Insert Item 158
- Insert Row 158
- Load From Selected File 158
- Load List From Step Sweep 159
- Load/Store 159
- Manual Mode Off On 159
- Manual Point 159
- Page Down 160
- Point Trigger 160
- Preset List 161
- Single Sweep 161
- Step Dwell 161
- Store to File 161
- Sweep Direction Down Up 162
- Sweep Repeat Single Cont 162
- Sweep Trigger 163
- Sweep Type List Step 163
- 4-110 User’s Guide 166
- ARB Catalog Types 167
- Black Pixels Screen Test 168
- Brightness 168
- Calibrate Selected Items 168
- Catalog Type 169
- Clear Error Queue(s) 169
- Copy File 170
- Delete All Files 172
- Deselect All Items 173
- Deselect Item 173
- Diagnostic Info 173
- Hardware Options 176
- Help Mode Single Cont 176
- 8648A/B/C/D 177
- 8656B,8657A/B 177
- 8657D NADC (Option UN8) 177
- 8657D PDC (Option UN8) 178
- 8657J PHS (Option UN8) 178
- GPIB Address 178
- GPIB/RS-232 179
- Installed Board Info 179
- Instrument Adjustments 179
- 4-124 User’s Guide 180
- Modify License Key 181
- Mod Status Info Off On 182
- Modulation Catalog Types 182
- Options Info 183
- Power On Last Preset 184
- Power On/Preset 184
- Preset Language 185
- Preset Normal User 185
- Proceed With Reconfiguration 185
- Recall Ref Osc Setting 186
- Receive Pace None Xon 186
- Ref Osc Coarse 186
- Ref Osc Fine 187
- Remote Language 187
- Rename File 187
- Reset RS-232 188
- RS-232 Baud Rate 189
- RS-232 Echo Off On 189
- RS-232 Pace 189
- RS-232 Timeout 189
- RTS/CTS Pacing 190
- Save User Preset 191
- Screen Saver Delay 191
- Screen Saver Mode 192
- Screen Saver Off On 192
- Select Item 192
- Software Options 193
- Step/Knob Ratio 194
- Store Ref Osc Setting 194
- Transmit Pace None Xon 195
- Update in Remote Off On 195
- View Next Error Message 195
- View Previous Error Message 196
- White Pixels Screen Test 196
- 5Memory Structure 197
- Memory Types 198
- Viewing Stored Files 199
- Copying Stored Files 200
- Renaming Stored Files 200
- Deleting Stored Files 200
- 6Safety and Regulatory 201
- Safety Notes 202
- Instrument Markings 203
- General Safety Considerations 204
- Statement of Compliance 205
- Assistance 206
- Certification 207
- Declaration of Conformity 208
- -3.GSGV Deutschland) 209
Relacionado con productos y manuales para De medición, control y control Agilent Technologies 77-4
(37 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.038 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales