Agilent Technologies E1356A Especificaciones Pagina 138
- Pagina / 149
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Appendix E
Strain Gage Multiplexer Error Messages
Table E-1 lists the error messages associated with the strain gage
multiplexer modules programmed by SCPI. See mainframe manual for a
complete list.
Table E-1. Strain Gage Multiplexer Error Messages
No. Title Potential Cause(s)
-211 Trigger ignored Trigger received when scan not enabled. Trigger received after scan
complete. Trigger too fast.
-213 Init ignored Attempting to execute an INIT command when a scan is already in
progress.
-224 Illegal parameter value Attempting to execute a command with a parameter not applicable to the
command.
+1500 External trigger source
already allocated
Assigning an external trigger source to a switchbox when the trigger source
has already been assigned to another switchbox.
+2000 Invalid card number Addressing a module (card) in a switchbox that is not part of the switchbox.
+2001 Invalid channel number Attempting to address a channel of a module in a switchbox that is not
supported by the module (e.g., channel 99 of a multiplexer module).
+2006 Command not
supported
Sending a command to a module (card) in a switchbox that is unsupported
by the module.
+2008 Scan list not initialized Executing INIT command with no scan <channel_list>.
+2009 Too many channels in
channel list
Attempting to address more channels than available in the switchbox.
+ 2010 Scan mode not allowed
on this card
Attempting to execute a SCAN:MODE which is not supported.
+ 2011 Empty channel list No valid channels in channel list.
+2012 Invalid channel range Invalid channel(s) specified in SCAN <channel_list> command. Attempting to
begin scanning when no valid channel list is defined.
+ 2017 Incorrect ARM:COUNt Attempting to run a downloaded scan list with ARM:COUNt set to value
other than 1.
+2600 Function not supported
on this card
Sending a command to a module (card) in a switchbox that is not supported
by the module or switchbox.
+2601 Channel list required Sending a command requiring a channel list without the channel list.
Appendix E Strain Gage Multiplexer Error Messages 137
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
- Contents 2
- WARNINGS 9
- Documentation History 9
- Safety Symbols 9
- BUSINESS REPLY MAIL 12
- Multiplexers 14
- Identifying the 15
- Terminal Module 15
- Setting the Card ID 17
- Selecting the 18
- Interrupt Line 18
- Internally Supplied 19
- Bridge Excitation 19
- Strain Gage 20
- Multiplexer 20
- Configurations 20
- Instrument 22
- Addressing 22
- Connecting the 23
- Chapter 2 24
- About This Chapter 24
- Terminal Module Configuration 24
- Bridge Selection 25
- Voltage Terminals 25
- Wiring a Terminal Module 27
- Strain Gage Wiring Diagrams 28
- 1/4 Bridge Diagrams 29
- 1/2 Bridge Diagrams 30
- Full Bridge 31
- Diagrams 31
- Connecting Relay 32
- Multiplexers to an 32
- External Voltmeter 32
- Connecting FET 33
- Chapter 3 34
- Dynamic Strain Measurements 38
- Rosette Measurements 40
- DISP "" 42
- Continued on Next Page 45
- Comments 48
- • This program makes 48
- Chapter 4 50
- Making Strain Measurements 50
- Unbalanced Bridge 51
- Measurement 51
- Technique 51
- Downloaded 52
- Unstrained 52
- References 52
- Equations 53
- Block Diagram 54
- Description 54
- The Wheatstone 55
- 120Ω and 350Ω 56
- MULTIMETER 57
- (VIA ANALOG BUS) 57
- Figure 4-7. The Wagner Ground 58
- 1/4 Bridge 59
- Measurements 59
- (QUARter) 59
- 1/2 Bridge 60
- Poisson 1/2 Bridge 61
- (HPOisson) 61
- Dummy Gage 61
- Bridge (FBPoisson) 63
- Bending Poisson Full 63
- Poisson Full Bridge 64
- (FPOisson) 64
- Reference 66
- SCPI Command Reference 68
- Numeric 1 - 32767 70
- CALibration 71
- CONFigure 72
- Numeric 1 - 99 74
- Boolean 0 75
- INITiate 76
- Subsystem Syntax MEASure 78
- [ROUTe:] 81
- Numeric cc00 - cc15 83
- Discrete NONE 86
- Discrete ABUS 87
- [SENSe:] 89
- Numeric as measured 91
- Numeric 00 - 07 91
- Numeric 1 to 32768 92
- Numeric 1 to 99 93
- Numeric 1 to 99 94
- Example Query Trigger Source 98
- IEEE 488.2 Common Commands 99
- Command Quick Reference 100
- Specifications 102
- Relay Life 104
- Appendix B 106
- Material Tables 107
- Strain Gage Diagnostics 108
- Leadwire Resistance 109
- Internal Half Bridge Voltage 112
- Shunt Verification 114
- Procedure 116
- Guard Voltage 117
- !Print the guard voltage 118
- Bridge Excitation Voltage 119
- Appendix D 120
- About This Appendix 120
- Register Addressing 121
- A16 Address Space 123
- Inside the 123
- Command Module 123
- Register Descriptions 124
- Relay Multiplexer Registers 124
- Device Type 125
- Register 125
- FET Multiplexer Registers 127
- Scan Control 129
- Scan Channel 129
- Delay Register 129
- The WRITE 130
- Registers 130
- Configuration 132
- Direct Channel 133
- Direct Control 133
- Programming Examples 134
- Reading the Device 135
- Type Register 135
- Appendix E 138
- 149
Relacionado con productos y manuales para Cajas De Interruptores En Serie Agilent Technologies E1356A
(93 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales