Agilent Technologies 3070 Manual de instalación Pagina 3
- Pagina / 116
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
© Agilent Techonolgies 2001–2003 Agilent 3070 System Installation Manual (MS Windows Version) ii
Table of Contents
Installing a Support Bay and Instrument Rack .......................................................................... 1-23
Introduction.......................................................................................................................... 1-23
Install the Testhead Module Umbilical Cable(s) (307X Only)............................................ 1-23
Install the GPIB Cables (307X Only) .................................................................................. 1-24
Setting-Up Other Hardware .......................................................................................................1-27
Install a Pay-Per-Use (PPU) Button Adapter....................................................................... 1-27
Setup the Testhead for Automation ..................................................................................... 1-30
Install AccessPlus Cables .................................................................................................... 1-32
Enabling the Testhead................................................................................................................ 1-33
Boot the Testhead ................................................................................................................ 1-33
Troubleshooting Testhead Boot........................................................................................... 1-33
Check the System Config File ............................................................................................. 1-34
Verifying the Vacuum Subsystem ............................................................................................. 1-36
Introduction.......................................................................................................................... 1-36
Install the Vacuum Manifold ............................................................................................... 1-36
Connect the Compressed Air ............................................................................................... 1-36
Check the Vacuum Actuation System ................................................................................. 1-36
Troubleshooting ................................................................................................................... 1-37
Verifying the Testhead............................................................................................................... 1-39
Run AutoAdjust All............................................................................................................. 1-39
Run Full Diagnostics ........................................................................................................... 1-39
Completing the Installation........................................................................................................ 1-40
Verify Strip Printer .............................................................................................................. 1-40
System Printer / Plotter........................................................................................................1-40
Stabilize the Testhead ..........................................................................................................1-40
Reinstall Covers................................................................................................................... 1-40
Make System Recovery and Backup Tapes......................................................................... 1-40
Turn System Administration Over to the Customer ............................................................ 1-40
Fill Out the System Support Log ......................................................................................... 1-40
Maintenance Records........................................................................................................... 1-41
About ScanWorks ................................................................................................................ 1-41
Installation Billing Information ........................................................................................... 1-41
- 3070 Board Test Systems 1
- Contents 2
- Table of Contents 3
- Setting Up the KVM 11
- Figure 1-1 Rear of testhead 17
- Setting Up the Strip 23
- Preparing the 24
- Testhead 24
- Attach the Site LAN Cable 26
- Powering the PDU 27
- Installation 28
- Installing a Support 29
- Bay and Instrument 29
- Aux Aux Aux Aux Aux Aux 31
- YES - 3070 32
- Setting-Up Other 33
- Hardware 33
- Right Pod, cover removed 34
- Pod door open 34
- To Com1 port 34
- PPU Buttons 35
- Dual Buttons Holder 35
- Install AccessPlus Cables 38
- Enabling the 39
- Check the System Config File 40
- Verifying the 42
- Vacuum Subsystem 42
- Completing the 46
- Maintenance Records 47
- About ScanWorks 47
- E9970-90001 Rev. J 10/2003 49
- In this Chapter 49
- Referenced Manuals 49
- Introduction 49
- Logging-On as 50
- The Root Directory 51
- Environment 51
- Variable 51
- ■ Use the correct case 53
- Directory 55
- Descriptions 55
- Lines Containing File Paths 56
- Use BT-BASIC 56
- Testhead Configuration 57
- System Config File 58
- BT-BASIC 62
- MS Windows Quick 63
- Reference 63
- BT-BASIC Quick 64
- Korn Shell Quick 65
- Quick Reference 68
- Codewords & 72
- Software License 72
- User and 73
- Specifics 74
- Config File 75
- <keywords> 76
- Standard Config 77
- File Specifics 77
- Board Config Files 78
- Compiling the 83
- System and 83
- Hardware Addresses 84
- IP Addresses 85
- Test Device Communication 86
- Location of Device Files 88
- DUT Power Supply Device Files 88
- Vacuum Control Specifics 89
- Rotating the 90
- DUT Power 93
- Supplies 93
- Controller Cables 97
- X2000 Controller 98
- X2100 Controller 101
- Series II/3 101
- System Card 101
- IPC Controller 104
- Series II/3 / 79000 104
- Private LAN and 107
- Serial Port MUX 107
- LAN Port 109
- Connections 109
- Troubleshooting 109
- Installing Drivers 110
- LAN Ports 110
- Administrator and click OK 111
- Printed in Singapore 116
- E9970-90001 Rev. H 116
Relacionado con productos y manuales para Multímetros Agilent Technologies 3070
(28 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.049 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales