Agilent Technologies N9360A Manual de usuario Pagina 41
- Pagina / 376
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Operating Procedures 4
N9360A Multi UE Tester W-CDMA User Manual 4-3
Test Preparat io n
The following procedures are require before proceeding with
any test:
System Requirements
• The following equipment are required to setup the test
system:
• The Agilent N9360A Multi UE Tester.
• An RF cable, RF antenna coupler (type N9360A-A02) or
shield case (part number type N9360A-S01) to connect RF
signals to the mobile phone under test.
• A printer and a printer cable if required.
Figure 4-2 Typi c al Te st S et u p
CAUTION
Make sure that the input signal level does not exceed the maximum
level allowed. Otherwise, Tester failure may occur.
- Agilent N9360A 1
- Multi UE Tester 1
- Notation 3
- Trademarks 4
- Additional Information: 6
- Performance Criteria: 6
- Contents 7
- List of Figures 13
- 5 Screen Reference 5-1 14
- 6 Troubleshooting 6-1 17
- List of Tables 19
- Legal Information 23
- Service And Support 25
- 1 Legal Information 26
- Agilent Technologies 27
- Safety Information 28
- When Operating The Tester 29
- Overview 31
- Functions 32
- Reference Sensitivity Level 33
- Features 34
- 3 Overview 36
- Accessories 37
- Operating Procedures 39
- Test Flow 40
- Test Preparat io n 41
- Installing The Test USIM 42
- Connections 42
- Connecting a Printer 43
- USB Memory Device 44
- Test Procedure 45
- Storing Numeric Values 48
- Recalling Numeric Values 50
- System Selection 52
- Figure 4-13 [Initial] Screen 55
- RF IN/OUT Loss Correction 57
- Sequence] Screen 61
- Downlink TX Power 63
- 6 Set the test condition 67
- Refer to “Saving Test Setup 83
- File" on page 5-171 83
- Handover 84
- 8 Set the input fields 87
- Refer to “Saving Test 91
- Emergency Call 92
- 6 Start Manual Test 99
- 4 Operating Procedures 100
- Set the input fields 101
- Operating Procedures 4 103
- Algorithm" 107
- 5 Set the Band fields 113
- Ending A Test 115
- Screen Reference 117
- Screen Flow Chart 118
- Top Menu Screen 119
- 5 Screen Reference 120
- Softkey Menu Field 121
- Softkey Menu 1 121
- Softkey Menu 2 121
- Screen Field 122
- Message Field 122
- Configuration Screen 123
- Softkey Menu 124
- Option Installation/Backup 127
- Option Backup 128
- Firmware Update Screen 129
- Softkey Menu 3 131
- Update Flash Screen 133
- Network Setting Screen 136
- Initial Screen 140
- Return to Menu Screen 143
- PRESET Select Mode Screen 144
- Automatic Test 146
- RF Test in Automatic Test 147
- TEST USIM 148
- Stand-by Screen 149
- Measuring Screen 155
- Measuring Talk Screen 159
- Abort Screen 163
- Explanation 166
- Sequence 2 Screen 167
- Measurement Result Screen 169
- Input Field (continued) 173
- Manual Test 175
- RF Test in Manual Test 176
- Softkey Menu 4 179
- Location Update Screen 183
- Softkey Field 184
- Connection Screen 188
- Screen Reference 5 189
- CPICH RSCP Screen 197
- SMS Screen 206
- HSDPA Screen 213
- HSDPA Measuring Screen 231
- TX Analyzer 242
- Screen Fields 246
- Signal Generator 256
- Configuration 261
- Softkey Menu-3 263
- W-CDMA Mode is set to HSDPA 278
- Saving Test Setup File 287
- Softkey Menu 1 S 290
- Recalling Test Setup File 292
- Deleting Test Setup File 296
- Troubleshooting 311
- Item To Be Checked 312
- Table 6-1 Item To Be Checked 313
- Error Information 314
- Error Codes for Error Screens 315
- 6 Troubleshooting 316
- Measurement Performance 318
- Frequency Error 319
- Error Vector Magnitude (EVM) 319
- Origin Offset 320
- Sensitivity/BER 320
- ACLR DSB 5MHz (W07 Option) 320
- ACLR DSB 10MHz (W07 Option) 321
- OBW (W07 Option) 321
- Choices or Ranges 323
- –99.99 to 0.00 330
- W-CDMA (FDD) System 333
- Frequency Bands 334
- TX-RX Frequency Separation 334
- Channel Number 335
- UE Maximum Output Power 336
- List of Abbreviations 337
- Introduction 342
- Specifications 342
- Operating the Antenna Coupler 343
- Channels 345
- Modulation is set to Idle 346
- Spreading code (non-HSDPA) 347
- Spreading code (HSDPA) 348
- DL reference channel (HSDPA) 351
- OCNS (non-HSDPA) 354
- OCNS Signal 355
- OCNS (HSDPA) 356
- Performance Test 359
- Open Loop Power 360
- Maximum Output Power 362
- Error Vector Magnitude 363
- Inner Loop Power 367
- Reference Sensitivity 371
- ACLR DSB 373
- Minimum TX Power 375
Relacionado con productos y manuales para Redes Agilent Technologies N9360A
Redes Agilent Technologies 8753ET Especificaciones
(262 paginas)
(262 paginas)
Redes Agilent Technologies 8753ET Guía de usuario
(546 paginas)
(546 paginas)
(21 paginas)
Redes Agilent Technologies 8753ES Guía de usuario
(245 paginas)
(245 paginas)
Redes Agilent Technologies N9360A Manual de usuario
(354 paginas)
(354 paginas)
Redes Agilent Technologies 81640A Guía de usuario
(114 paginas)
(114 paginas)
Redes Agilent Technologies E6474A Manual de servicio
(52 paginas)
(52 paginas)
Redes Agilent Technologies J3972A Guía de usuario
(551 paginas)
(551 paginas)
Redes Agilent Technologies 8922S Manual de usuario
(18 paginas)
(18 paginas)
Redes Agilent Technologies 81689A Guía de usuario
(117 paginas)
(117 paginas)
Redes Agilent Technologies N9360A Manual de usuario
(10 paginas)
(10 paginas)
Redes Agilent Technologies 8753ES Manual de usuario
(13 paginas)
(13 paginas)
(47 paginas)
Redes Agilent Technologies 8922S Especificaciones
(204 paginas)
(204 paginas)
Redes Agilent Technologies E6474A Guía de usuario
(184 paginas)
(184 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.080 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales