Agilent Technologies 8487D Guía de usuario Pagina 166
- Pagina / 196
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Error Messages
Error Messages
4-8 Agilent E4418B User’s Guide
-230 Data corrupt or stale;Please zero and calibrate Channel A
When CAL[1|2]:RCAL is set to ON and the sensor currently connected
to channel A has not been zeroed and calibrated, then any command
which would normally return a measurement result (for example
FETC?, READ?, or MEAS?) will generate this error message.
-230 Data corrupt or stale;Please zero Channel A
When CAL[1|2]:RCAL is set to ON and the sensor currently connected
to channel A has not been zeroed, then any command which would
normally return a measurement result (for example FETC?, READ?, or
MEAS?) will generate this error message.
-230 Data corrupt or stale;Please calibrate Channel A
When CAL[1|2]:RCAL is set to ON and the sensor currently connected
to channel B has not been calibrated, then any command which would
normally return a measurement result (for example FETC?, READ?, or
MEAS?) will generate this error message
-231 Data questionable;CAL ERROR
Power meter calibration failed. The most likely cause is attempting to
calibrate without applying a 1 mW power to the power sensor.
-231 Data questionable;Input Overload
The power input to Channel A exceeds the power sensor’s maximum
range.
-231 Data questionable;Lower window log error
This indicates that a difference measurement in the lower window has
given a negative result when the units of measurement were
logarithmic.
-231 Data questionable;Upper window log error
This indicates that a difference measurement in the upper window has
given a negative result when the units of measurement were
logarithmic.
-231 Data questionable;ZERO ERROR
Power meter zeroing failed. The most likely cause is attempting to zero
when some power signal is being applied to the power sensor.
HP4402.book Page 8 Wednesday, November 29, 2000 4:46 PM
- User’s Guide 1
- Legal Information 3
- Limitation of Warranty 4
- Exclusive Remedies 4
- Equipment Operation 5
- General Safety Considerations 6
- IEC 1010-1 Compliance 7
- Statement of Compliance 7
- User Environment 7
- Installation Instructions 7
- Regulatory Information 8
- Declaration of Conformity 9
- List of Related Publications 10
- Available Accessories 11
- About this Guide 12
- Table of Contents 13
- List of Figures 17
- List of Tables 19
- Getting Started 21
- Turning On the Power Meter 23
- The Front Panel at a Glance 24
- The Display Layout 27
- Selecting Your Display Layout 31
- Window Symbols 34
- 1 of N Entry Window 35
- The Rear Panel at a Glance 36
- Adjusting the Carrying Handle 38
- Rack Mounting the Power Meter 39
- General Information 43
- Running Time 43
- Charging Times 44
- Backlight 44
- Battery Removal/Replacement 45
- Zeroing the Power Meter 47
- Zero/Cal Lockout 47
- Calibrating the Power Meter 48
- 1 2 3 4 5 6 7 8 52
- Power Sensors 55
- Making the Measurement 60
- Offset Tables 67
- Making Relative Measurements 74
- Setting the Resolution 75
- Setting Offsets 76
- Setting Averaging 78
- Step Detection 79
- Measuring Pulsed Signals 81
- Setting Measurement Limits 83
- Setting Window Limits 84
- Checking for Limit Failures 87
- Setting the Range 92
- RS232/RS422 94
- Remote Interface Overview 96
- Recorder Output 99
- Leveling a Source Output 100
- Power Meter Operation 101
- Lower Window 103
- Presetting the Power Meter 104
- Self Test 106
- Remote Testing 109
- Test Descriptions 110
- Operator Maintenance 113
- Check the Basics 115
- Instrument serial numbers 115
- GB12345678 116
- Sales and Service Offices 117
- Latin America: 118
- United States: 118
- Menu Reference 121
- Introduction 122
- The Front Panel Menu Maps 123
- Frequency/Cal Fac Menu 124
- Meas Setup Menu 125
- Rel/Offset Menu 126
- Save/Recall Menu 126
- System Inputs Menu (1 of 4) 127
- System Inputs Menu (2 of 4) 128
- System Inputs Menu (3 of 4) 129
- System Inputs Menu (4 of 4) 130
- Zero/Cal Menu 131
- Front Panel Menu Reference 132
- Frequency 133
- TTL Inputs Off On 155
- Diagrammatical Hardkeys 156
- Error Messages 159
- Specifications 171
- Power Meter Specifications 173
- Accuracy 174
- Power Reference 175
- Measurement Speed 176
- Zero Drift of Sensors 177
- Measurement Noise 177
- Settling Time 179
- Power Sensor Specifications 182
- General Characteristics 184
- Environmental Characteristics 185
- Dimensions 186
- Remote Programming 186
- Non-Volatile Memory 187
- 3-19, 3-26 192
Relacionado con productos y manuales para Multímetros Agilent Technologies 8487D
Multímetros Agilent Technologies 34410A Guía de usuario
(190 paginas)
(190 paginas)
Multímetros Agilent Technologies 83622A Guía de usuario
(331 paginas)
(331 paginas)
Multímetros Agilent Technologies DC140 Guía de usuario
(137 paginas)
(137 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.067 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales