Agilent Technologies E1330B Manual de usuario Pagina 112
- Pagina / 156
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
110 Agilent E1330B Digital I/O Module Register Information
Appendix B
The module is a register-based slave/interrupter device, supporting VME
D16, D8(O), and D8(OE) transfers. The interrupt protocol supported is
“release on interrupt acknowledge” – an interrupt is cleared by a VXIbus
interrupt acknowledge cycle.
WARNING Registers have been documented as 8 bit bytes. If you access
them using 16 bit transfers from a Motorola CPU, the high and
low byte will be swapped. The Agilent E1300/01 Mainframe and
Agilent E1405/06 Command Modules use Motorola CPUs.
Motorola CPUs place the highest weighted byte in the lower
memory location and the lower weighted byte in the higher
memory address; Intel processors do just the opposite. VXI
registers are memory mapped, thus you will see this
Motorola/Intel byte swap difference when doing register
programming.
- *E1330-90007* 1
- Contents 3
- 2 Contents 4
- Contents 3 5
- 4 Contents 6
- Certification 7
- Safety Symbols 8
- WARNINGS 8
- Documentation History 8
- DECLARATION OF CONFORMITY 9
- Getting Started 13
- 12 Getting Started 14
- Chapter 1 14
- Table 1-1. Data Lines 14
- Instrument Definition 15
- Downloading SCPI Drivers 15
- SCPI Command 16
- Format Used in This 16
- Specifying SCPI 16
- Commands 16
- Specifying Multiple Port 17
- Operations 17
- Initial Operation 18
- Chapter 2 19
- Using This Chapter 19
- Setting the Address Switch 20
- Enabling Pull-ups 21
- Selecting the Interrupt Line 22
- Combining the Flag Lines 23
- Using with External Pull-ups 30
- Typical Connection 31
- Chapter 3 33
- Addressing the Module 33
- Operation Overview 34
- Default and Reset States 35
- Setting the Polarity 35
- Setting the Handshake Mode 36
- Inputting Data Bytes and Bits 37
- Multiple Port Operations 39
- Using Trace Memory 40
- I/O Module 43
- The CTL Line 44
- Using the Handshake Modes 46
- Chapter 4 47
- 0 or 1. Byte or 53
- Multiple Port 56
- Input/Output 56
- Command Reference 59
- SCPI Command Reference 62
- DISPlay Subsystem 63
- :MONitor[:STATe]? 65
- MEASure Subsystem 66
- Parameters 67
- Comments 69
- MEMory Subsystem 70
- :VME:STATe 73
- • *RST Condition: Set to OFF 73
- :VME:STATe? 73
- [SOURce:] Subsystem 74
- 0.000002. MAX returns 0.015 81
- DIGital:DATAn[:type]:POLarity 84
- DIGital:DATAn[:type]:TRACe 85
- DIGital:FLAGn:POLarity 88
- DIGital:FLAGn:POLarity? 88
- DIGital:TRACe:DEFine? 94
- DIGital:TRACe:DELete:ALL 94
- DIGital:TRACe:DELete[:NAME] 94
- STATus Subsystem 95
- :OPERation:CONDition? 96
- :OPERation:ENABle 96
- :OPERation:ENABle? 96
- :OPERation[:EVENt]? 96
- :QUEStionable:CONDition? 97
- :QUEStionable:ENABle 97
- :QUEStionable:ENABle? 97
- :QUEStionable[:EVENt]? 97
- SYSTem Subsystem 98
- • Related Commands: *ERR 99
- • *RST Condition: None 99
- :VERSion? 99
- IEEE 488.2 Common Commands 100
- Command Quick Reference 101
- Chapter 5 104
- Appendix A 105
- Information 107
- A16 Address Space 108
- Outside the Command 108
- Module or Mainframe 109
- Inside the Command 109
- Reset and Registers 111
- Register Definitions 111
- Appendix B 112
- Register Descriptions 113
- Port Interrupt 114
- Control Register 114
- Port Transfer 115
- Port Control/ 116
- Status Register 116
- Port Handshake 118
- Register 118
- Table B-4. Handshake Type 119
- Table B-5. Range Multipliers 119
- Port Normalization 120
- Programming Examples 123
- Resetting the 124
- Reading the 125
- ID, Device 125
- Type, and 125
- Registers 125
- C Version 126
- Writing an 127
- 8-Bit Byte 127
- Writing a 129
- 16-Bit Word 129
- Reading an 130
- PIR Interrupts 133
- Agilent E1330 133
- B Non-data 138
- Line I/O 138
- Embedded 142
- Computer 142
- Error Messages 145
- 144 Error Messages 146
- Appendix C 146
- Agilent E1330B User’s Manual 147
- 146 Index 148
- C (continued) 149
- 148 Index 150
- I (continued) 151
- M (continued) 152
- P (continued) 153
- R (continued) 154
- S (continued) 155
Relacionado con productos y manuales para Multímetros Agilent Technologies E1330B
Multímetros Agilent Technologies 83630A Especificaciones
(133 paginas)
(133 paginas)
Multímetros Agilent Technologies 34411A Guía de usuario
(152 paginas)
(152 paginas)
Multímetros Agilent Technologies 8487D Guía de usuario
(196 paginas)
(196 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.096 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales