Agilent Technologies Agilent G1369B Manual de usuario descargar pdf (Pagina 15)

Agilent 1260 Infinity High Performance Autosampler User Manual 15

Introduction

Autosampler Principle

When the sample sequence begins, the valve unit switches to the bypass

position. Solvent from the pump enters the valve unit at port 1, and flows

directly to the column through port 6.

Figure 2 Bypass Position

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 205 206

Agilent 1260 Infinity 1
High Performance 1
Autosampler 1
In This Guide 3
Contents 5
Features 10
Overview of the Module 11
1 Introduction 12
Autosampler Principle 13
Injection Sequence 14
System Overview 19
Agilent Technologies 23
Site Requirements 24
Power Cords 25
Bench Space 26
Condensation 26
Physical Specifications 27
Specifications 28
Installing the Autosampler 31
Unpacking the Autosampler 32
Delivery Checklist 33
3 Installing the Autosampler 34
One Stack Configuration 36
Two Stack Configuration 38
Using the Module 47
Leak and Waste Handling 48
Preparing the Autosampler 49
4 Using the Module 50
& 53
' 53
Control Settings 55
Method Parameter Settings 56
Module Configuration 60
(G4208A) 61
Optimizing Performance 65
Delay Volume 66
5 Optimizing Performance 68
Status Indicators 80
Error Messages 80
Module Status Indicator 82
User Interfaces 83
Agilent Lab Advisor Software 84
Error Information 85
7 Error Information 86
What are Error Messages 87
General Error Messages 88
Remote Timeout 89
Lost CAN Partner 89
Leak Sensor Open 90
Leak Sensor Short 91
Compensation Sensor Open 91
Compensation Sensor Short 92
Fan Failed 92
Module Error Messages 93
Side Door Error 94
Valve to Bypass Failed 95
Valve to Mainpass Failed 95
Needle Lock Failed 96
Needle Carrier Failed 97
Initialization Failed 99
Metering Home Failed 100
Motor Temperature 101
Invalid Vial Position 102
Peristaltic Pump Error 103
Vessel or Wash Vessel Error 103
Vessel Stuck to Needle 104
Rear Blind Seat Missing 104
Test Functions 105
Introduction 106
System Pressure Test 107
8 Test Functions 108
Maintenance Positions 112
Change Needle 113
Change Loop Capillary 113
Arm Position 114
Change Needle Carrier 114
Change Metering Device 115
Injector Steps 116
Step Commands 117
Maintenance 119
Introduction to Maintenance 120
Warnings and Cautions 121
Overview of Maintenance 122
Cleaning the module 123
Removing the needle assembly 124
9 Maintenance 126
Exchanging the Needle Seat 130
Replacing the Rotor seal 132
Removing the Metering Seal 135
>chZgiidda 137
Tools required Description 143
Flat head screwdriver 143
Parts required # Description 143
1 Interface board 143
Replacing the Module Firmware 144
Parts for Maintenance 145
10 Parts for Maintenance 146
Vial Trays 147
Recommended Vial Plates 149
Accessory Kit 150
Injection Ugrade Kit 150
Analytical Head Assembly 151
Injection Valve Assembly 152
Cover Parts 153
Leak System Parts 154
Identifying Cables 155
Cable Overview 156
Analog Cables 158
Remote Cables 160
11 Identifying Cables 162
BCD Cables 163
CAN/LAN Cables 165
External Contact Cable 166
Agilent Module to PC 167
Hardware Information 169
Firmware Description 170
GZh^YZciHnhiZb 171
BV^c;LjeYViZ 171
BV^cHnhiZb 171
GZh^YZci;LJeYViZ 171
12 Hardware Information 172
Obstruction of transport unit 173
Electrical Connections 174
Rear view of the module 175
Interfaces 176
Overview Interfaces 179
>chigjbZci 180
BVaZ ;ZbVaZ ;ZbVaZ BVaZ 180
APG Remote 181
Special Interfaces 182
Special Settings 186
Instrument Layout 187
Early Maintenance Feedback 188
LAN Configuration 189
13 LAN Configuration 190
Connecting the module via LAN 191
Appendix 193
General Safety Information 194
Operation 195
Safety Symbols 196
Lithium Batteries Information 197
(2002/96/EC) 198
Radio Interference 199
Sound Emission 200
Use of Solvents 201
14 Appendix 202
*G1367-90014* 206

Comentarios a estos manuales

Sin comentarios

Agilent Technologies Agilent G1369B Manual de usuario Pagina 15

Comentarios a estos manuales