Agilent Technologies B2902 Guía de usuario Pagina 85
- Pagina / 232
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Agilent B2900 User’s Guide, Edition 2 3- 9
Installation
Maintenance
1. If it is in the remote state, press the Cancel / Local key.
2. Press the On/Off switch and confirm that the switch turns off.
3. Disconnect test leads and cables from the channel terminals.
4. Press the following function keys.
More > System > Cal/Test > Self-Test
Confirmation dialog box is opened.
5. Press the OK key. This starts the self-test.
Self-calibration
Agilent B2900 provides the self-calibration function to maintain the measurement
performance. If the environmental temperature changes 3 C or more, perform the
self-calibration. This is effective for the accurate measurements by minimizing the
effect of thermal drift. The self-calibration must be performed after warming-up of
60 minutes. Before performing the self-calibration, turn the channel output off and
disconnect test leads and cables from the terminals.
To perform
self-calibration
The following procedure shows how to perform the self-calibration.
1. If it is in the remote state, press the Cancel / Local key.
2. Press the On/Off switch and confirm that the switch turns off.
3. Disconnect test leads and cables from the channel terminals.
4. Press the following function keys.
More > System > Cal/Test > Self-Cal
Confirmation dialog box is opened.
5. Press the OK key. This starts the self-calibration.
Calibration
Calibration and adjustments must be performed periodically so that the instruments
satisfy the specifications, and keep a good condition. It is recommended to perform
the calibration once a year at least. For the calibration and adjustments, contact your
nearest Agilent Sales and Support Office. Trained service personnel will perform the
calibration and adjustments.
- Agilent B2900 Series 1
- Precision Source/Measure Unit 3
- Safety Summary 5
- Safety Symbols 7
- Product Stewardship 15
- In This Manual 16
- Contents 17
- 1 Getting Started 25
- D: Dual view 26
- 1: Single view 26
- Applying DC Output 27
- **UDSK9LHZ 31
- Operation Tips 32
- Operation Summary 34
- View key 37
- Getting Started 40
- 2 Introduction 41
- Front View 44
- Rear View 47
- Serial Number 48
- Source/Measure Unit 49
- Measurement Parameters 50
- Limit/Compliance 50
- Output and Measurement Ranges 51
- Specification Conditions 56
- Maximum Voltage and Current 56
- Source Specifications 56
- Measurement Specifications 56
- Pulse peak 60
- Pulse width 60
- Pulse base 60
- Output Characteristics 63
- Resistance Measurement 65
- System Speeds 65
- General Specifications 67
- Front Panel Interface 68
- Easy-to-use Key Operations 68
- Sweep Measurement 70
- Data Buffers 70
- Programming Language 71
- USB File System 71
- Digital I/O Interface 72
- Software and Drivers 73
- Furnished Accessories 74
- Available Accessories 74
- 3 Installation 77
- Inspecting the Shipment 79
- Checking for Errors 80
- Safety Considerations 81
- Environment 81
- Connecting the Power Cord 81
- Bench Installation 82
- Rack Installation 83
- Removing the Bumper 83
- Removing the Handle 83
- Cleaning 84
- Self-test 84
- Self-calibration 85
- Calibration 85
- Connecting a DUT 86
- Floating 88
- Using Test Leads 89
- Using the N1295A Test Fixture 90
- Using the 16442B Test Fixture 91
- 2-wire connections 92
- 4-wire connections 92
- Guarding 94
- $QRGH 96
- &DWKRGH 96
- Installation 97
- GPIB/USB Interfaces 98
- LAN Interface 100
- Connecting to a Site LAN 100
- Modifying the LAN Settings 101
- Communicating Over the LAN 102
- Using Telnet 103
- Using Sockets 103
- Using Digital I/O 105
- 4 Front Panel Reference 107
- Hard Keys and Rotary Knob 109
- Display and Assist Keys 111
- Dual View 112
- Single View 114
- Range parameters 117
- Sweep parameters 118
- Pulse parameters 120
- Trigger parameters 121
- Graph View 123
- Roll View 125
- Status Information 128
- Function Keys 129
- Config key group 130
- Output Connection dialog box 131
- Output Filter dialog box 132
- Sweep dialog box 133
- Ranging dialog box 134
- Wait Control dialog box 135
- Math Expression dialog box 136
- Limit Test Setup dialog box 138
- Trace Buffer Setup dialog box 140
- Trigger key group 141
- Measure Result dialog box 144
- Limit Test Result dialog box 145
- File Selection dialog box 147
- Program key group 148
- I/O key group 149
- Data Output Format 150
- Format (Measure) dialog box 150
- Format (Trace) dialog box 151
- LAN Configuration dialog box 152
- DIO Configuration dialog box 152
- DIO Read/Write dialog box 153
- Display key group 154
- System key group 155
- 5 Front Panel Operations 157
- Starting measurement 158
- Basic Operations 159
- Setting the Power Frequency 161
- Setting the Beeper 162
- Setting the Date and Time 162
- Performing the Self-Test 162
- Displaying the Error Message 163
- Clearing the Error Buffer 163
- Clearing Timestamp 163
- Setting the GPIB Address 164
- Front Panel Operations 165
- Controlling the Source Output 165
- Stopping the Source Output 166
- Setting the Output Range 166
- Setting the Pulse Output 167
- Setting the Sweep Output 168
- Setting the List Sweep Output 169
- Setting the Source Wait Time 170
- Setting the Output Filter 170
- Setting the Connection Type 171
- Protection 172
- Function 173
- Setting the Sweep Direction 174
- Setting the Measurement Mode 176
- Performing Spot Measurement 176
- Stopping Measurement 176
- Setting the Measurement Speed 176
- Setting the Measurement Range 177
- Performing Sweep Measurement 177
- Using the Math Function 181
- Performing the Limit Test 182
- Setting the Trace Buffer 186
- Selecting a Program 188
- 6 Function Details 189
- To Set Compliance 191
- Setting the Ranging Mode 192
- Aperture Time 193
- Overhead Time 193
- Pulse Output 195
- To Set Pulse Output 196
- Sweep Output 197
- List Sweep 198
- Output Filter 199
- Output-Off Status 201
- High Capacitance Mode 203
- Resistance Compensation 204
- Predefined Math Expressions 205
- Limit Test 208
- Function Details 209
- Trace Buffer 211
- Program Memory 213
- Channel Grouping 214
- Trigger Source 215
- ARM Layer 216
- TRIGger Layer 216
- Device Actions 217
- Trigger Output 218
- Synchronous Device Actions 219
- Interlock Function 220
- Over Temperature Protection 221
- Initial Settings 222
Relacionado con productos y manuales para Multímetros Agilent Technologies B2902
Multímetros Agilent Technologies N9340A Guía de usuario
(161 paginas)
(161 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.144 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales