Agilent Technologies E8257C PSG Guía de usuario Pagina 191
- Pagina / 220
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 9 181
Two-Tone Waveform Generator
Creating, Viewing, and Modifying Two-Tone Waveforms
Creating, Viewing, and Modifying Two-Tone Waveforms
This section describes how to set up, generate, and modify a two-tone waveform while viewing it with a
spectrum analyzer. Although you can view a generated two-tone signal using any spectrum analyzer that has
sufficient frequency range, an Agilent Technologies PSA Series High-Performance Spectrum Analyzer was
used for this demonstration. Before generating your signal, connect the spectrum analyzer to the signal
generator as shown in Figure 9-1.
Figure 9-1 Spectrum Analyzer Setup
To Create a Two-Tone Waveform
This procedure describes how to create and a basic, center-aligned, two-tone waveform.
1. Preset the signal generator.
2. Set the signal generator RF output frequency to 20 GHz.
3. Set the signal generator RF output amplitude to 0 dBm.
4. Press
Mode > Two Tone > Freq Separation > 10 > MHz.
5. Press
Two Tone Off On to On.
6. Turn on the RF output.
The two-tone signal is now available at the signal generator RF OUTPUT connector. Figure 9-2 shows what
the signal generator display should look like after all steps have been completed. Notice that the T-TONE,
I/Q, RF ON, and MOD ON annunciators are displayed and the parameter settings for the signal are shown
in the status area of the signal generator display.
- User’s Guide 1
- Contents 10
- 1 Signal Generator Overview 11
- Firmware Upgrades 14
- Modes of Operation 15
- Front Panel 16
- Recall hardkey 17
- 8. Trigger 18
- 9. MENUS 18
- 10. Help 18
- 11. EXT 1 INPUT 18
- Mod On/Off hardkey 19
- 35. DATA CLOCK INPUT 22
- 36. SYMBOL SYNC INPUT 22
- 33. I/Q INPUTS 22
- 34. DATA INPUT 22
- Front Panel Display 23
- 3. Annunciators 24
- 5. Amplitude Area 26
- 6. Error Message Area 26
- 7. Text Area 26
- 8. Softkey Label Area 26
- Rear Panel 27
- 1. AC Power Receptacle 28
- 3. AUXILIARY INTERFACE 28
- 11. EVENT 1 30
- 12. EVENT 2 30
- 13. PATTERN TRIG IN 30
- 14. BURST GATE IN 30
- 15. AUXILIARY I/O 31
- 16. Digital Bus 32
- 17. WIDEBAND I INPUT 32
- 18. WIDEBAND Q INPUT 32
- 20. I OUT 32
- 21. I-bar OUT 33
- 22. Q OUT 33
- 23. Q-bar OUT 33
- 24. BASEBAND GEN REF IN 33
- 26. 10 MHz OUT 34
- 27. 10 MHz IN 34
- 28. 10 MHz EFC (Option UNR) 34
- 2 Basic Operation 35
- Using Table Editors 36
- Table Editor Softkeys 37
- Configuring the RF Output 38
- OFFS indicator 39
- Ampl Offset > 10 > dB 40
- RF On/Off 43
- Single Sweep 43
- Sweep Repeat Single Cont 43
- Sweep Type List Step 44
- Configure List Sweep 44
- Markers 50
- Turn Off Markers 52
- Sweep/List 52
- Configure Ramp/Step Sweep 52
- Freq Start 52
- Return > Sweep > Off 54
- Return > Sweep > Ampl 54
- Modulating a Signal 60
- Using Data Storage Functions 62
- Enabling Options 67
- 3 Optimizing Performance 69
- Using External Leveling 70
- Configure Cal Array 77
- GPIB Listener Mode 79
- 4 Analog Modulation 87
- Analog Modulation Waveforms 88
- Configuring AM 89
- Configuring FM 90
- Configuring ΦM 91
- Configuring Pulse Modulation 92
- Configuring the LF Output 93
- 86 Chapter 4 96
- Analog Modulation 96
- First-Level Softkey Men 99
- (Some ARB formats 99
- Amplitude hardkey menu 101
- Chapter 5 93 103
- 94 Chapter 5 104
- Select Waveform softkey 105
- ARB Off On to On 105
- Current waveform file type 107
- Waveform File Type 107
- Accessing the Dual ARB Player 109
- Creating Waveform Segments 110
- Playing a Waveform 112
- Editing a Waveform Sequence 112
- Renaming a Waveform Segment 113
- Using Waveform Markers 114
- To Verify Marker Operation 117
- Waveform Marker Concepts 118
- Using Waveform Triggers 121
- Using Waveform Clipping 122
- Waveform Clipping Concepts 123
- Chapter 5 117 127
- 118 Chapter 5 128
- Custom Arb Waveform Generator 129
- Overview 130
- −625 kHz and a 133
- Working with Filters 135
- Using a Predefined FIR Filter 136
- Edit Keys > Clear Text 141
- 132 Chapter 6 142
- Working with Symbol Rates 143
- 134 Chapter 6 144
- Chapter 6 135 145
- Working with Modulation Types 146
- Configuring Hardware 153
- To Set the ARB Reference 154
- Custom Real Time I/Q Baseband 155
- Working with Data Patterns 157
- Edit File 160
- Cursor moves to new position 161
- Position indicator changes 161
- Bits 4C through 4F inverted 162
- Hex Data changed 162
- Working with Burst Shapes 163
- Return > Return > 166
- Editing Keys > Clear Text 166
- To Adjust the I/Q Scaling 169
- Working with Phase Polarity 170
- Using Differential Encoding 175
- 1 > Enter 176
- +/- > 1 > Enter 176
- 2 > Enter 176
- 0 > Enter 177
- 168 Chapter 7 178
- Multitone Waveform Generator 179
- Freq Spacing > 1 > MHz 181
- Multitone Off On to On 181
- To View a Multitone Waveform 182
- Toggle State 183
- Edit Item > -10 > dB 184
- Edit Item > 123 > deg 184
- Apply Multitone 184
- Multitone 184
- 9 Two-Tone Waveform Generator 189
- To Create a Two-Tone Waveform 191
- To View a Two-Tone Waveform 192
- Chapter 9 183 193
- Two-Tone Waveform Generator 193
- Figure 9-3 193
- Chapter 9 185 195
- Figure 9-4 195
- Two Tone 196
- 10 Troubleshooting 197
- 188 Chapter 10 198
- Troubleshooting 198
- RF Output Power Problems 199
- Sweep Problems 204
- Configure Step Sweep 205
- Step Dwell softkey 205
- Data Storage Problems 206
- Cannot Turn Off Help Mode 207
- Signal Generator Locks Up 208
- Preset key 209
- Error Messages 210
- Error Message Format 211
- Error Message Types 212
- 204 Chapter 10 214
- , 29, 30 218
Relacionado con productos y manuales para Generadores De Poder Agilent Technologies E8257C PSG
(291 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.057 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales