Agilent Technologies 8133A Manual de servicio Pagina 114
- Pagina / 188
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
114 16800 Series Portable Logic Analyzers Service Guide
6 Replacing Assemblies
16800 Series Logic Analyzer Disassembly/Assembly
This chapter contains the instructions for removing and
replacing the assemblies of the logic analyzer. Also in this
chapter are instructions for returning assemblies.
Replacement Strategy
Some procedures in this section tell you to remove other
assemblies of the instrument, but do not give complete
instructions. In these cases, refer to the procedure for that
specific assembly for the instructions. The drawings here are
representative. Your parts may look different.
Tools Required
• T6, T10, T15, T25 TORX screwdrivers.
• #1 Pozi- drive screwdriver.
• 13/16 inch, deep- well nut driver.
• 5 mm nut driver.
• 1/4- inch hollow- shaft nut driver.
WARNING
Hazardous voltages exist on the power supply. To avoid electrical
shock, disconnect power from the instrument before performing
the following procedures. After disconnecting the power, wait at
least six minutes for the capacitors on the power supply board to
discharge before servicing the instrument.
CAUTION
Damage can occur to electronic components if you remove or
replace assemblies when the instrument is on or when the power
cable is connected. Never attempt to remove or install any assembly
with the instrument on or with the power cable connected.
CAUTION
Electrostatic discharge can damage electronic components. Use
grounded wrist straps and mats when performing any service to this
logic analyzer.
- Agilent 16800 Series 1
- Portable Logic Analyzers 1
- Model Comparison 3
- Features, Logic Acquisition 3
- Features, Mainframe 4
- Features, Pattern Generator 4
- Supplied Accessories 4
- Optional Accessories: 4
- Service Strategy 4
- In this Service Guide 6
- 4 Calibrating and Adjusting 8
- 7 Replaceable Parts 10
- 8 Theory of Operation 10
- Contents 11
- General Information 13
- Accessories 14
- Specifications 15
- Characteristics 16
- Non-Operating Environment 17
- Dimensions 18
- Recommended Test Equipment 19
- 1 General Information 20
- Preparing for Use 21
- To inspect the logic analyzer 22
- To apply power 22
- To clean the instrument 23
- To start the user interface 23
- To test the logic analyzer 23
- 2 Preparing for Use 24
- Testing Performance 25
- To perform the power-up tests 26
- Logic Analyzer Test Strategy 27
- 3 Testing Performance 28
- Testing Performance 3 31
- Equipment Required 34
- Perform System Self-Tests 36
- Set Up the Test Equipment 37
- Connect the Test Equipment 39
- Deskew the oscilloscope 42
- Set the 8133A pulse width 43
- Configure the Logic Analyzer 45
- Run eye finder 49
- To re-align a stray channel 50
- Test Pod 1 in 250 Mb/s Mode 52
- Test Pod 2 in 250 Mb/s Mode 57
- Test the remaining pods 59
- Test Pod 1 in 500 Mb/s Mode 60
- Test Pod 2 in 500 Mb/s Mode 64
- Conclude the State Mode Tests 66
- Performance Test Record 68
- Calibrating and Adjusting 69
- Calibration Strategy 70
- Troubleshooting 71
- Try , and then 75
- Power Supplies 84
- To run the self-tests 88
- Bit#: 39 - 16 15 - 8 7 - 0 92
- Clock Test 93
- Simple RAM Test 93
- RAM Persistence Test 94
- Marching Bits RAM Test 94
- Wait Test 94
- Instruction Interrupt Test 95
- To exit the test system 96
- 5 Troubleshooting 100
- Set up the test equipment 101
- Connect the test equipment 101
- Threshold 102
- Troubleshooting 5 109
- Clock Frequency of 100 MHz 111
- Click Run Rep 111
- Replacing Assemblies 113
- Replacement Strategy 114
- Tools Required 114
- To save the license file 115
- To power off the system 116
- Replacing Assemblies 6 117
- 6 Replacing Assemblies 118
- 600 watt power supply 119
- Secondary power supply 120
- 60 mm fan 144
- 92 mm fans 145
- Returning Assemblies 148
- FRAGILE 149
- Replaceable Parts 151
- Ordering Replaceable Parts 152
- System Replaceable Parts List 155
- Replaceable Parts 7 159
- • A — Assembly 163
- • MP — Mechanical Part 163
- • W — Cable 163
- Theory of Operation 167
- System Block Level Theory 168
- Module Interface Board (MIB) 169
- CPU Subsystem 170
- PCI board 171
- MIB (Module Interface Board) 171
- Module Bus FPGA(s) 172
- I/O FPGA 172
- Theory of Operation 8 173
- Front Panel Assembly 174
- Power Up Routine 175
- Product install 178
- Software recovery methods 178
- Self Test 179
- Comparators 181
- Acquisition IC 181
- Master/Expander Connectors 182
- Instruction Memory 183
- Data Memory 183
- Output Driver 184
- Clock Circuit 184
- CPU Interface 184
Relacionado con productos y manuales para De medición, control y control Agilent Technologies 8133A
(145 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.048 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales