Agilent Technologies B2902 Manual de servicio Pagina 113
- Pagina / 326
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Agilent B2900 SCPI Command Reference, Edition 2 3- 9
Common Commands
*OPC
*OPC
This command starts to monitor pending operations, and sets/clears the operation
complete (OPC) bit in the Standard Event Status register as follows.
• If there is no pending operation, the OPC bit is set to 1.
• If there are any pending operations, the OPC bit is set to 0. The bit will be set to
1 again when all pending operations are completed.
The *OPC command is required to enable the OPC bit. To stop monitoring pending
operations (disable OPC bit), execute the
*CLS command.
Other commands cannot be executed until this command completes.
Syntax *OPC
*OPC?
Query response 1 <newline><^END>
The query returns 1 if the instrument has completed all pending operations sent
before this command. Response data type is NR1.
See Also *WAI
- Agilent B2900 Series 1
- In This Manual 4
- Contents 10
- 1 Programming Basics 17
- SCPI Commands 19
- Moving Between Subsystems 20
- Including Common Commands 21
- Using Queries 21
- Coupled Commands 21
- SCPI Messages 22
- Message Unit Separator 23
- Root Specifier 23
- Query Indicator 23
- Message Terminator 23
- Numeric Suffix 24
- Channel List Parameter 24
- SCPI Command Completion 25
- Data Output Format 28
- Status Data 29
- GPIB Capability 33
- Status Byte 34
- Status System Diagram 35
- Programming Basics 36
- Non-Volatile Settings 39
- 2 Subsystem Command Summary 41
- Setting Source/Measure Unit 44
- Subsystem Command Summary 45
- • [:SOUR[c]]:WAIT:AUTO OFF 54
- =CURRent 58
- •:SENS[c]:WAIT:AUTO OFF 61
- Source Output Ranges 64
- Duty cycle ~ 2.5 % 66
- Duty cycle ~ 99.9999 % 66
- Measurement Ranges 67
- TRANsient device action 69
- ACQuire device action 69
- Trigger is generated after 70
- ARM Layer 71
- TRIGger Layer 71
- Reading Source/Measure Data 77
- STAR and 85
- Using Advanced Functions 91
- 3 Common Commands 105
- 4 Subsystem Commands 123
- CALCulate Subsystem 125
- :CALCulate:CLIMits:MODE 127
- :CALCulate:CLIMits:STATe 127
- :CALCulate:CLIMits:STATe:ANY? 128
- :CALCulate:CLIMits:UPDate 128
- :CALCulate:DATA? 129
- :CALCulate:DATA:LATest? 130
- :CALCulate:DIGital:BIT 130
- :CALCulate:FEED 131
- :CALCulate:LIMit:FAIL? 133
- :CALCulate:LIMit:FUNCtion 134
- :CALCulate:LIMit:STATe 136
- :CALCulate:MATH:DATA? 136
- :CALCulate:MATH:DATA:LATest? 137
- Predefined math expressions 140
- :CALCulate:MATH:STATe 142
- :CALCulate:MATH:UNITs 143
- :CALCulate:OFFSet 143
- :CALCulate:OFFSet:ACQuire 144
- :CALCulate:OFFSet:STATe 144
- DISPlay Subsystem 145
- :DISPlay:ENABle 146
- :DISPlay:VIEW 146
- :DISPlay[:WINDow]:DATA? 147
- :DISPlay[:WINDow]:TEXT:DATA 148
- :DISPlay[:WINDow]:TEXT:STATe 148
- :DISPlay:ZOOM 149
- FETCh Subsystem 150
- :FETCh[:SCALar]? 152
- ATus 153
- Subsystem Commands 154
- Example :FETC:CURR? (@2,1) 154
- FORMat Subsystem 155
- :FORMat:DIGital 156
- :FORMat:ELEMents:CALCulate 156
- :FORMat:ELEMents:SENSe 157
- :FORMat:SREGister 158
- HCOPy Subsystem 159
- LXI Subsystem 160
- :LXI:MDNS:HNAMe[:RESolved]? 161
- :LXI:MDNS:SNAMe:DESired 161
- :LXI:MDNS:SNAMe[:RESolved]? 161
- Other LXI Subsystem Commands 162
- LXI Trigger Events 164
- MEASure Subsystem 166
- MMEMory Subsystem 168
- :MMEMory:COPY 169
- :MMEMory:DELete 170
- :MMEMory:LOAD:MACRo 170
- :MMEMory:LOAD:STATe 170
- :MMEMory:MDIRectory 170
- :MMEMory:MOVE 171
- :MMEMory:RDIRectory 171
- LL]> 172
- :MMEMory:STORe:MACRo 172
- :MMEMory:STORe:STATe 173
- :MMEMory:STORe:TRACe 173
- OUTPut Subsystem 175
- :OUTPut:HCAPacitance[:STATe] 177
- :OUTPut:LOW 178
- :OUTPut:OFF:AUTO 178
- :OUTPut:OFF:MODE 179
- :OUTPut:ON:AUTO 180
- :OUTPut:PROTection[:STATe] 180
- :OUTPut:RECall 181
- :OUTPut:SAVE 181
- :OUTPut[:STATe] 182
- PROGram Subsystem 183
- :PROGram:PON:RUN 184
- :PROGram[:SELected]:APPend 184
- :PROGram[:SELected]:DEFine 184
- :PROGram[:SELected]:EXECute 186
- :PROGram[:SELected]:NAME 187
- :PROGram[:SELected]:STATe 187
- :PROGram[:SELected]:WAIT? 188
- :PROGram:VARiable 188
- READ Subsystem 190
- :READ[:SCALar]? 192
- Tus 193
- SENSe Subsystem 195
- NPLCycles 196
- NPLCycles:AUTO 197
- [:LEVel] 198
- :TRIPped? 198
- RANGe:AUTO 199
- RANGe:AUTO:LLIMit 200
- TO:THReshold 202
- RANGe:AUTO:ULIMit 202
- RANGe[:UPPer] 203
- :SENSe:DATA? 204
- :SENSe:DATA:LATest? 205
- :SENSe:FUNCtion:OFF 205
- :SENSe:FUNCtion:OFF:ALL 206
- :SENSe:FUNCtion:OFF:COUNt? 206
- :SENSe:FUNCtion[:ON] 206
- :SENSe:FUNCtion[:ON]:ALL 207
- :SENSe:FUNCtion[:ON]:COUNt? 207
- :SENSe:FUNCtion:STATe? 207
- :SENSe:REMote 208
- :SENSe:RESistance:MODE 208
- :SENSe:TOUTput:SIGNal 210
- :SENSe:TOUTput[:STATe] 210
- :SENSe:WAIT:AUTO 211
- :SENSe:WAIT:GAIN 212
- :SENSe:WAIT:OFFSet 212
- :SENSe:WAIT[:STATe] 213
- SOURce Subsystem 214
- :AMPLitude] 215
- [:SOURce]:DIGital:DATA 221
- BEFore 223
- [:SOURce]:FUNCtion:MODE 225
- [:SOURce]:FUNCtion[:SHAPe] 225
- [:SOURce]:PULSe:DELay 228
- [:SOURce]:PULSe:WIDTh 229
- [:SOURce]:SWEep:DIRection 229
- [:SOURce]:SWEep:POINts 230
- [:SOURce]:SWEep:RANGing 231
- [:SOURce]:SWEep:SPACing 232
- [:SOURce]:SWEep:STAir 232
- [:SOURce]:TOUTput:SIGNal 233
- [:SOURce]:TOUTput[:STATe] 233
- [:SOURce]:WAIT:AUTO 234
- [:SOURce]:WAIT:GAIN 235
- [:SOURce]:WAIT:OFFSet 235
- [:SOURce]:WAIT[:STATe] 236
- STATus Subsystem 237
- NTRansition 241
- PTRansition 242
- :STATus:PRESet 242
- SYSTem Subsystem 248
- :SYSTem:COMMunicate:ENABle 249
- :SYSTem:COMMunicate:LAN:DHCP 251
- :SYSTem:COMMunicate:LAN:DNS 252
- :SYSTem:COMMunicate:LAN:MAC? 253
- :SYSTem:COMMunicate:LAN:SMASk 254
- :SYSTem:COMMunicate:LAN:WINS 256
- :SYSTem:DATA:QUANtity? 256
- :SYSTem:DATE 257
- :SYSTem:ERRor:ALL? 257
- :SYSTem:ERRor:CODE:ALL? 257
- :SYSTem:ERRor:CODE[:NEXT]? 258
- :SYSTem:ERRor:COUNt? 258
- :SYSTem:ERRor[:NEXT]? 258
- :SYSTem:FAN:MODE 259
- :SYSTem:GROup[:DEFine] 259
- :SYSTem:GROup:RESet 260
- :SYSTem:INTerlock:TRIPped? 260
- :SYSTem:LANGuage 260
- :SYSTem:LFRequency 261
- :SYSTem:LOCK:NAME? 262
- :SYSTem:LOCK:OWNer? 262
- :SYSTem:LOCK:RELease 262
- :SYSTem:LOCK:REQuest? 263
- :SYSTem:PON 263
- :SYSTem:PRESet 264
- :SYSTem:SET 264
- :SYSTem:TIME 264
- :SYSTem:TIME:TIMer:COUNt? 265
- :SYSTem:VERSion? 266
- TRACe Subsystem 267
- :TRACe:FEED 268
- :TRACe:FEED:CONTrol 268
- :TRACe:FREE? 269
- :TRACe:POINts 269
- :TRACe:POINts:ACTual? 270
- :TRACe:STATistic:DATA? 270
- :TRACe:STATistic:FORMat 270
- :TRACe:TSTamp:FORMat 271
- TRIGger Subsystem 272
- 275
- EXT11 275
- 282
- EXT10 282
- 284
- LAN 284
- 285
- 5 Error Messages 287
- No Error 289
- Command Error 290
- Execution Error 294
- Device-Dependent Error 296
- Query Error 297
- B2900 Specific Error 298
- Error Messages 308
Relacionado con productos y manuales para De medición, control y control Agilent Technologies B2902
(25 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.076 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales