Agilent Technologies AGILENT U2761A Manual de servicio descargar pdf (Pagina 97)

Agilent U2761A USB Modular Function/Arbitrary Waveform Generator

Programmer’s Reference

Agilent Technologies

Frequency Sweep Commands

[SOURce:]FREQuency:STARt 90

[SOURce:]FREQuency:STOP 91

[SOURce:]SWEep:SPACing 92

[SOURce:]SWEep:TIME 93

[SOURce:]SWEep:STATe 94

This section describes the Frequency sweep commands used to configure

the sweep settings of the U2761A. These commands allow you to set the

start and stop frequency values, sweep spacing, sweep time, and sweep

state.

1 2 ... 92 93 94 95 96 97 98 99 100 101 102 ... 168 169

Agilent U2761A 1
USB Modular 1
Function/Arbitrary 1
Waveform Generator 1
Contents 3
Instrument errors 152 7
Self-test errors 153 7
Calibration errors 153 7
Arbitrary waveform errors 155 7
Introduction to SCPI 9
Mnemonic forms 10
Command separators 11
Using a comma ( , ) 12
Using whitespace 12
Using “?” commands 12
Syntax conventions 13
Square brackets “[ ]” 14
Parenthesis “( )” 14
Syntax diagram conventions 15
Data types and formats 16
Input message terminators 17
Using device clear 18
SCPI Status System 19
1 Introduction to SCPI 20
Questionable Data register 21
Standard Event register 22
Status Byte register 23
IEEE-488.2 Common Commands 25
Parameter 27
2 IEEE-488.2 Common Commands 38
APPLy Commands 39
Using the APPLy Command 40
APPLy:SINusoid 41
APPLy:SQUare 42
APPLy:RAMP 43
APPLy:PULSe 44
APPLy:DC 45
APPLy:USER 46
3 APPLy Commands 48
Output Configuration Commands 49
[SOURce:]FUNCtion[:SHAPe] 50
SOUR : FREQ space 52
SOUR : VOLT space 53
:LEV :IMM :UNIT VPP 58
SOUR : FUNC space 59
:SQU :DCYC percent 59
:RAMP :SYMM percent 60
OUTP :STAT space 61
OUTP :LOAD space 62
Pulse Configuration Commands 65
SOUR : PULS space 66
:PULS :HOLD WIDT 67
:PULS :WIDT seconds 68
:PULS :DCYC percent 70
Modulation Commands 71
[SOURce:]AM:INTernal:FUNCtion 72
SOUR : AM space 74
[SOURce:]FM:INTernal:FUNCtion 77
SOUR : FM space 79
SOUR : PM space 84
Shift Keying Commands 87
SOUR : ASK space 88
SOUR : FSK space 90
SOUR : PSK space 93
7 Shift Keying Commands 96
Frequency Sweep Commands 97
SOUR : SWE space 100
:SPAC LIN 100
Triggering Commands 103
TRIG :SEQ space:SOUR IMM 104
Examples 105
TRIG :SEQ :IMM 106
TRIG :SEQ space:SLOP POS 107
OUTP :TRIG space:SLOP POS 108
OUTP :TRIG space 110
Arbitrary Waveform Commands 111
DATA:DAC VOLATILE 112
FORM space 114
:BORD NORM 114
DATA:ATTRibute:AVERage? 115
DATA:ATTRibute:CFACtor? 116
DATA :ATTR :POIN ? 117
DATA:ATTRibute:PTPeak? 118
SYSTem Commands 119
SYSTem:CDEScription? 120
SYSTem:ERRor? 121
SYSTem:VERSion? 122
Phase-Lock Commands 123
SOUR : PHAS space:SOUR INT 124
SOUR : PHAS space 125
UNIT space 126
:ANGL DEG 126
SOUR : PHAS :REF 127
:UNL :ERR :STAT 128
OUTP :PHAS space 129
12 Phase-Lock Commands 130
Status Reporting Commands 131
STATus:PRESet 132
STAT ?:QUES :COND 133
STATus:QUEStionable:ENABle 134
STAT :QUES ?:EVEN 136
CALibration Commands 137
CAL space:SEC OFF 138
:STAT , code 138
CAL space:SEC :CODE new code 139
CALibration:SETup 140
CAL space 141
CAL :COUN ? 142
14 CALibration Commands 144
CONFigure Command 145
:SSI , @address , address( ) 146
15 CONFigure Command 148
Error Messages 149
Error Messages 16 151
Execution errors 152
16 Error Messages 154
Device-dependent errors 159
Query errors 160
Instrument errors 160
Self-test errors 161
Calibration errors 161
Arbitrary waveform errors 163
Factory Default Settings 165
Factory Default Settings 17 167
17 Factory Default Settings 168
Agilent Technologies 169

Comentarios a estos manuales

Sin comentarios

Agilent Technologies AGILENT U2761A Manual de servicio Pagina 97

Comentarios a estos manuales

Relacionado con productos y manuales para No Agilent Technologies AGILENT U2761A