Agilent Technologies HP 3325B Manual de instrucciones Pagina 213
- Pagina / 252
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 6 Backdating
The Agilent 53131A Calibration Procedures
Assembly-Level Service Guide 6-11
6
CHANGE 1 (Firmware Revisions 3317, 3335, 3402, 3427) (Continued)
To Calibrate the Gain for Channels 1 and 2
1 Press any one of the arrow keys until CAL: GAIN 1 ? is displayed.
2 Press Enter key.
A scrolling message is displayed. Follow the instruction by performing the following
steps.
3 Connect a BNC tee connector to Channel 1 of the Counter.
4 Connect the Counter, dc power supply, and multimeter as shown in Figure 2-1.
Figure 2-1. Gain Calibration Setup
5 Adjust the power supply until the multimeter displays + 5.000 V ± 0.001 V.
6 Disconnect the digital multimeter from the Counter to prevent noise from being
introduced into the measurement.
7 Press Enter key.
The Counter momentarily displays CALIBRATING, and then it should display GAIN
1 PASS.
If the fail message is displayed, refer to the troubleshooting section in this chapter.
+
--
DC Power Supply
HP 53131A
Counter Digital Multimeter
BNC Tee
- Printed in Malaysia 1
- Agilent 53131A/132A/181A 3
- Assembly-Level Service Guide 3
- DECLARATION OF CONFORMITY 6
- Contents 10
- 2 Service 11
- 3 Replacing Assemblies 13
- 4 Retrofitting Options 13
- 5 Replaceable Parts 14
- 6 Backdating 14
- How to Use This Guide 17
- How to Order Guides 19
- Hardware 22
- Accessories Supplied 23
- Accessories Available 23
- Performance Tests 25
- Complete Performance Tests 27
- Optional GPIB Verification 27
- Recommended Calibration Cycle 27
- Test Record 27
- Equipment Required 28
- Power-On Self Tests 29
- P 53131A/132A 30
- P 53181A 31
- HP 3458A 32
- Counter Setup 34
- External Timebase Tests 36
- HP53131A/132 42
- Pulse Generator 42
- HP 3325B 44
- Synthesizer 44
- (Agilent 53131A/132A Only) 46
- 050 only) 57
- 124 only) 58
- Channel 2 62
- Volt Peak 2 63
- (Optional) 64
- (Page 1 of 6) 65
- (Page 2 of 6) 66
- (Page 3 of 6) 67
- (Page 4 of 6) 68
- (Page 5 of 6) 69
- (Page 6 of 6) 70
- (Agilent 53181A Only) 75
- HP 8663A 76
- Synthesized Signal Generator 76
- Frequency Sensitivity 82
- (Page 1 of 4) 95
- (Page 2 of 4) 96
- (Page 3 of 4) 97
- (Page 4 of 4) 98
- Introduction 100
- To Provide Repair Information 101
- On / Stby 104
- Scale & 106
- To Unsecure for Calibration 107
- HP 59992A J06 110
- Time Interval Calibrator 110
- HP 53131A/132A 110
- To Secure Against Calibration 111
- To View the Calibration Count 112
- DC Power Supply 116
- Counter Digital Multimeter 116
- To Calibrate Time Interval 117
- CAL: TI QUIK? Calibration 118
- Equipment 118
- CAL: TI FINE? Calibration 119
- Channel 1 121
- Chapter 2 Service 125
- for Channel 1 129
- HP 53181A 131
- Digital Multimeter 131
- Safety Considerations 134
- Recommended Test Equipment 135
- Repair Considerations 136
- Electrostatic Discharge 136
- Surface Mount Repair 136
- After Service Considerations 137
- Product Safety Checks 137
- Product Performance Checks 137
- Service Center 138
- Troubleshooting the Counter 143
- Motherboard 144
- Assembly 144
- To Run the Test-All Self Test 147
- Replacing Assemblies 151
- Tools Required 153
- Do This First 153
- To Remove the Cover 154
- SERIAL PLATE 155
- To Remove the Front Bezel 156
- Rubber foot 166
- A4 AC Power 166
- Supply Assembly 166
- (Option 002) 167
- (Options 001, 010, and 012) 169
- A6 High Stability 170
- Timebase Assembly 170
- Retrofitting Options 175
- Preliminary Procedure 178
- Retrofitting Procedure 179
- Procedure 186
- Jumper cap 187
- Plug (MP9) 189
- Replaceable Parts 193
- Exchange Assemblies 194
- Reference Designations 195
- How To Order A Part 196
- Cabinet Parts and Hardware 198
- Chapter 5 Replaceable Parts 199
- Assemblies) 201
- Backdating 203
- Manual Changes 204
- Older Instruments 204
- Backdating Hardware 205
- CHANGE 3 (New TCXO boards) 206
- Option 002 208
- Option 015 208
- Option 030 208
- Option 050 208
- Backdating Firmware 210
- Chapter 6 Backdating 211
- HP 53131A 213
- HP53131A 215
- Counter 215
- HP 8130A 215
- Pulse Generator 215
- Backdating Specifications 218
- Instrument Inputs (Continued) 223
- Time Base 224
- Measurement Specifications 225
- Input Frequency (Hz) 226
- Frequency Error (Hz) 227
- Time Interval 229
- Frequency Ratio: 229
- Pulse Width 230
- Rise/Fall Time 230
- Totalize 231
- Peak Volts 231
- Duty Cycle 231
- Trigger Level Timing Errors 232
- ⁄⁄⁄⁄⁄⁄⁄⁄ 233
- Gate Time 234
- Measurement Throughput 234
- Measurement Arming 234
- Measurement Statistics 235
- Measurement Limits 235
- General Information 236
- Agilent 53181A Specifications 237
- Worst Case RMS Resolution 242
- Frequency Error (Hz) 242
- Input Frequency 242
- Measurement Definitions 245
- NUMERICS 249
© 2020, manymanuals.es. Todos los derechos reservados | 0.053 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales