Agilent Technologies 54657A Especificaciones Pagina 150
- Pagina / 188
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
• To order a part in the material list, quote the Agilent Technologies
part number, indicate the quantity desired, and address the order to
your nearest Agilent Technologies Sales Office.
• To order a part not listed in the material list, include the model
number and serial number of the oscilloscope, a description of the
part (including its function), and the number of parts required.
Address the order to your nearest Agilent Technologies Sales Office.
• To order using the direct mail order system, contact your nearest
Agilent Technologies Sales office.
Within the USA, Agilent Technologies can supply parts through a direct mail
order system. The advantages to the system are, direct ordering and
shipment from the Agilent Technologies Parts Center in Roseville, California.
There is no maximum or minimum on any mail order. (There is a minimum
amount for parts ordered through a local Agilent Technologies Sales Office
when the orders require billing and invoicing.) Transportation costs are
prepaid (there is a small handling charge for each order) and no invoices.
In order for Agilent Technologies to provide these advantages, a check or
money order must accompany each order. Mail order forms and specific
ordering information are available through your local Agilent Technologies
Sales Office. Addresses and telephone numbers are located in a separate
document shipped with the instrument.
Service
Replacing Parts in the Oscilloscope
4-58
- Agilent 54615B, 54616B 1
- Oscilloscopes 1
- Accessories supplied 3
- Accessories available 3
- Options available 4
- Contents 7
- 4Service 8
- 5 Performance Characteristics 9
- Glossary 10
- The Oscilloscope at a Glance 11
- Figure 1–1 13
- Figure 1–2 13
- Figure 1–3 14
- Press Autoscale 17
- To set up the vertical window 18
- To expand the vertical signal 20
- To set up the time base 21
- ▼ happened before the 22
- To trigger the oscilloscope 23
- Mode 24
- Slope/Coupling 25
- To use roll mode 26
- Using Color (54616C only) 27
- To print in color 30
- Operating Your Oscilloscope 31
- To use delayed sweep 33
- Time reference set to left 34
- Delayed sweep 34
- Time reference set to center 35
- Press Autostore 36
- Erase 37
- Autostore 37
- To capture a single event 38
- Find the glitch 40
- Press Time 44
- Press the Freq softkey 44
- Press the Next Menu softkey 47
- Press the Rise Time softkey 48
- Press Voltage 50
- Press the Vrms softkey 51
- To make cursor measurements 53
- Figure 2-11 54
- Figure 2-12 54
- Figure 2-13 55
- Figure 2-14 55
- Figure 2-15 56
- Figure 2-16 56
- To save or recall traces 63
- Press Setup 64
- To reset the instrument setup 65
- To use the XY display mode 66
- Press Cursors 67
- Figure 2-26 69
- Figure 2-27 69
- To analyze video waveforms 70
- Using Option 005 Enhanced 73
- TV/Video Trigger 73
- To select TV display grid 76
- Cursors key 77
- Triggering on All Lines 79
- Triggering on Field 1 80
- Serration pulses 80
- Equalizing pulses 80
- Figure 3-7 85
- Figure 3-8 87
- Figure 3-9 87
- CALIBRATOR 98
- Set up the oscilloscope 100
- To verify bandwidth 102
- To verify trigger sensitivity 107
- 100 MHz, 75 mV p-p 109
- Adjusting the Oscilloscope 113
- To adjust the power supply 114
- (top side of oscilloscope) 116
- +5.1 V adjust 116
- –5.25 V adjust 116
- CALIBRATOR output 118
- ∆V(2) for ∆V(1) 120
- Model/Part 121
- 19, and 20 125
- Is the fan running? 128
- To clear error messages 129
- Perform the keyboard test 134
- Perform the ROM test 135
- Perform the RAM test 135
- To troubleshoot Option 005 136
- To replace an assembly 138
- To remove the fan 139
- To remove the front panel 139
- To remove the display 141
- To remove the system board 141
- To remove the attenuator 142
- To remove the power supply 146
- To remove the keyboard 147
- To remove the handle 148
- To order a replacement part 149
- Figure 4-12 151
- Figure 4–13 152
- Reference 153
- Designator 153
- Agilent Part 153
- Qty Description 153
- Figure 4-14 156
- Performance Characteristics 159
- Horizontal System 162
- Trigger System 163
- TV Functions 164
- XY Operation 164
- Display System 164
- Acquisition System 165
- Advanced Functions 166
- Power Requirements 166
- (54615B and 54616B only) 167
- General (54616C only) 169
- (54615B, 54616B, and 54616C) 170
- Option 005 Trigger System 172
- Oscilloscope Terms 173
- TV/Video Trigger Terms 177
- Glossary–8 180
- DECLARATION OF CONFORMITY 185
© 2020, manymanuals.es. Todos los derechos reservados | 0.062 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales