Agilent Technologies ESG Especificaciones Pagina 129
- Pagina / 170
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
ESG Family Signal Generators Adjustments
FM/PM YO Frequency Compensation Calibration (ESG-AP and ESG-DP only)
Calibration Guide 5-23
FM/PM YO Frequency Compensation Calibration
(ESG-AP and ESG-DP only)
Description
This adjustment calibrates the FM/PM YIG oscillator frequency compensation latches on
the YO driver assembly. These latches adjust the flatness of the YO FM/PM paths for rates
greater than 100 kHz. The “FM In-Band DAC Offset Calibration” on page 5-15 and the
“FM/PM Out-of-Band Calibration (ESG-AP and ESG-DP only)” on page 5-22 must be
performed prior to this adjustment.
Required Test Equipment
• HP/Agilent 8563E Spectrum Analyzer
• HP/Agilent 33120A 15 MHz Function/Arbitrary Waveform Generator
Procedure
Figure 5-19FM/PM YO Freq. Compensation Setup
1. Connect the equipment as shown above.
2. Preset all of the equipment.
3. Follow the instructions as they appear on the controller’s display.
- Agilent Technologies 1
- ESG Family Signal Generators 1
- Contents 3
- 1Equipment Required 7
- Required Equipment 8
- Low Noise Amplifiers for 10
- 2Operation Verification 11
- Verification Procedures 12
- 2. Check for Error Messages 13
- 4. Power Level Accuracy Check 14
- Configure the Signal Generator 15
- Configure the Power Meter 15
- 5. FM Accuracy Check 17
- 6. AM Accuracy Check 18
- Measure the Deviations 19
- Test Tables 20
- Calibration Guide 2-11 21
- Calibration Guide 22
- Calibration Guide 2-13 23
- Calibration Guide 2-15 25
- Calibration Guide 2-17 27
- Calibration Guide 2-19 29
- 2-20 Calibration Guide 30
- 3Service Software 31
- Calibration Guide 3-3 33
- 3-4 Calibration Guide 34
- Next button 34
- Uninstalling the Software 35
- Software Configuration 36
- The User Configuration 37
- Identifying the DUT 37
- Adding Test Equipment 38
- Calibration Guide 3-9 39
- Removing Test Equipment 40
- Editing Test Equipment 41
- Adding Device Drivers 42
- Calibration Guide 3-13 43
- Removing Device Drivers 44
- Adding Test Drivers 44
- Calibration Guide 3-15 45
- 3-16 Calibration Guide 46
- Removing Test Drivers 47
- Adding Datapacks 47
- 3-18 Calibration Guide 48
- Removing Datapacks 49
- Starting the Software 50
- Equipment 52
- Calibration Guide 3-23 53
- 3-24 Calibration Guide 54
- Calibration Guide 3-25 55
- 3-26 Calibration Guide 56
- Exiting the Software 57
- 3-28 Calibration Guide 58
- 4Performance Tests 59
- 4-2 Calibration Guide 60
- Support Software 61
- 4-4 Calibration Guide 62
- 4-6 Calibration Guide 64
- Figure 4-4 The Save As Window 64
- 4-8 Calibration Guide 66
- Equipment Setups 68
- Calibration Guide 4-11 69
- 4. FM Frequency Response 71
- 5. AM Frequency Response 72
- Calibration Guide 4-19 77
- 9. Harmonic, Subharmonic, and 78
- Nonharmonic Spurious Signals 78
- 10. Power Level Accuracy 79
- 11. Timebase Aging Rate 82
- 4-26 Calibration Guide 84
- (Option UN8 only) 87
- (Option UNA only) 93
- Measuring Phase Noise 95
- Using an HP/Agilent 8644B 96
- Calibration Guide 4-39 97
- 4-40 Calibration Guide 98
- Measuring Residual FM 99
- (Option UND only) 100
- Calibration Guide 4-43 101
- Recommended Equipment 102
- Equipment Setup 102
- Performance Test Records 104
- Calibration Guide 4-47 105
- Frequency (GHz) 106
- 5Adjustments 107
- Adjustment Relationships 108
- • FM Path Offset Adjustment 109
- Required Test Equipment 110
- Procedure 110
- Analog Bus ADC Calibration 111
- Description 112
- Internal Source Calibration 113
- Timebase DAC Calibration 118
- FM Path Offset Calibration 120
- Modulation Source 124
- (ESG-A and ESG-D only) 126
- (ESG-AP and ESG-DP only) 129
- DCFM Calibration 130
- Prelevel Calibration, Digital 135
- Gain Adjust Calibration 137
- Low Noise Floor Gain Adjust 138
- VBLO Mixer Bias Calibration 140
- Power Level Accuracy 141
- ≥ 10 MHz and ≤ 2 GHz) Setup 143
- > 2 GHz) Setup 143
- Level Meter Calibration 144
- AM Gain Calibration 146
- 5-44 Calibration Guide 150
- 6Maintenance and Service 151
- Cleaning the Cabinet 152
- Cleaning the Display 152
- Sales and Service Offices 153
- 6-4 Calibration Guide 154
- 7Safety and Regulatory 155
- Safety Notes 156
- Instrument Markings 157
- General Safety Considerations 158
- Statement of Compliance 159
- Electrostatic Discharge 160
- Warranty 161
- Assistance 162
- Certification 163
- 7-10 Calibration Guide 164
- Index I-1 165
- I-2 Index 166
- Index I-3 167
- I-4 Index 168
- Index I-5 169
- I-6 Index 170
Relacionado con productos y manuales para Generadores De Poder Agilent Technologies ESG
(534 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.040 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales