Agilent Technologies 8000 Series Manual del operador Pagina 113
- Pagina / 126
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Maintenance and Troubleshooting 5
8000 Operator’s Manual 113
12 Install the new seal into the syringe port, making sure that it lays flat
in the bottom of the port and that the media path is not obstructed.
13 Install the syringe into the valve. Tighten by hand (18 - 21 oz-in,
1.3 - 1.5 Kg-cm).
14 Extend syringe plunger so that it is aligned with the plunger pin on
the pump.
15 Carefully install the syringe and valve assembly onto the valve and
plunger pins.
16 Replace the syringe valve retainer block and tighten the screws.
17 Reinstall the syringe plunger thumb screw(s).
18 Place the pump upright and connect the power cord and
communication cables.
19 Turn on the pump.
20 Connect all sample tubes to the pump.
21 Check for leaks using the 8000.
Cleaning the Syringes
To clean the syringes, use the appropriate cleaning solution based on the
product being tested. Ensure the sampling cannulas of the dissolution
apparatus are submerged into the cleaning solution. Syringes should be
cleaned after each test using one of the following procedures:
50% Methanol or 10% Bleach Cleaning Procedure
1 From the 8000 Ready screen, press MENU > 7. The Manual
Operations screen displays.
2 Select option 6, Syringe/Filter. The Operate Syringe/Filter Changer
screen displays.
3 Select option 1, Valve to Input, to ensure the valve is set to input.
4 Select option 3, Syringe Fill.
NOTE
The pump will initialize and compress all of the syringe plungers when
turned on.
- Agilent 8000 1
- Dissolution Sampling 1
- Contents 3
- 4 8000 Operator’s Manual 4
- 8000 Operator’s Manual 5 5
- 6 8000 Operator’s Manual 6
- 8000 Operator’s Manual 7 7
- 8 8000 Operator’s Manual 8
- 8000 Operator’s Manual 9 9
- 10 8000 Operator’s Manual 10
- Electrical Hazards 12
- Information Symbols 14
- Introduction 15
- 8000 with Peristaltic Pump 17
- CC1234xxxx 18
- Setting Up the 8000 19
- Unpacking Your 8000 21
- Installation 22
- Setup of 8000 and Components 34
- Installing the Sample Tray 36
- (Peristaltic Pump only) 37
- Installing the RM Module 38
- External Unit 39
- Hidden Key Functions 41
- 42 8000 Operator’s Manual 42
- 3 Setting Up the 8000 42
- Table 1 Hidden Key Functions 42
- Setting Up the 8000 3 43
- 8000 Operator’s Manual 43 43
- 44 8000 Operator’s Manual 44
- Operating the 8000 45
- 8000 Keypad Options 46
- Operating the 8000 4 47
- 8000 Operator’s Manual 47 47
- Main Menu 48
- 8000 Operator’s Manual 49 49
- 50 8000 Operator’s Manual 50
- 52 8000 Operator’s Manual 52
- 54 8000 Operator’s Manual 54
- 56 8000 Operator’s Manual 56
- 60 8000 Operator’s Manual 60
- Creating a Sample Program 61
- 8000 Operator’s Manual 63 63
- 64 8000 Operator’s Manual 64
- SAMPLE TIME POINT: 000:02 65
- Starting a 8000 Program 66
- 68 8000 Operator’s Manual 68
- DISSO Options Screen 69
- 70 8000 Operator’s Manual 70
- 8000 Operator’s Manual 71 71
- 8000 Operator’s Manual 73 73
- 8000 Operator’s Manual 75 75
- 76 8000 Operator’s Manual 76
- 78 8000 Operator’s Manual 78
- 82 8000 Operator’s Manual 82
- ON R-M PUMP displays 84
- 8000 Operator’s Manual 85 85
- 88 8000 Operator’s Manual 88
- 8000 Operator’s Manual 89 89
- Starting a Program 91
- APP 3/7 Options Screen 93
- 94 8000 Operator’s Manual 94
- Table 2 4 App 3/7 Options 94
- Manual Sample 95
- 96 8000 Operator’s Manual 96
- Automatic Calibration 97
- 1 MANUAL 2 AUTOMATIC 98
- Manual Calibration 99
- Daisy Chaining 102
- 104 8000 Operator’s Manual 104
- 4 Operating the 8000 104
- Agilent Technologies 105
- Preventive Maintenance 106
- Apparatus 3 / 7 107
- Start Immediately 108
- Programmed Clean 108
- Apparatus 1 / 2 111
- Syringe and Seal Replacement 112
- Cleaning the Syringes 113
- Filter Changer (optional) 115
- Report Center Impact Printer 119
- Replacing a Paper Roll 120
- Toggling Your Printer Online 121
- Printer Self Test 121
- Printer Configuration 122
- 124 8000 Operator’s Manual 124
- 8000 Operator’s Manual 125 125
- 126 8000 Operator’s Manual 126
Relacionado con productos y manuales para Impresión y escaneo Agilent Technologies 8000 Series
(82 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.049 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales